Introduction to the Agilent 7100 Capillary Electrophoresis System

More documents

Recommendations

Info

4 LAN Configuration Configuration Switch Configuration Switch The configuration switch can be accessed on the right rear side of the instrument. The 7100 CE is shipped with switches 7 and 8 set to ON. This means that the instrument is set to a fixed default IP: 192.168.254.11 NOTE To perform any LAN configuration, SW1 and SW2 must be set to OFF. Table 17 Factory default settings Initialization ('init') mode Link configuration Using default, switches 7 and 8 set to ON. Speed and duplex mode determined by auto-negotiation 64 Agilent 7100 Capillary Electrophoresis System User Manual
LAN Configuration 4 Initialization Mode Selection Initialization Mode Selection The following initialization (init) modes are selectable: Table 18 Initialization mode switches SW6 SW7 SW8 Init mode OFF OFF OFF Bootp OFF OFF ON Bootp & Store OFF ON OFF Using Stored OFF ON ON Using Default Bootp When the initialization mode "Bootp" is selected, the 7100 CE tries to download the parameters from a Bootp server. The parameters obtained become the active parameters immediately. They are not stored in the non-volatile memory of the 7100 CE. Therefore, the parameters are lost with the next power cycle of the 7100 CE. Figure 3 Bootp (principle) Agilent 7100 Capillary Electrophoresis System User Manual 65
Page 1 and 2:
Agilent 7100 Capillary Electrophore
Page 3 and 4:
In This Guide… This guide contain
Page 5 and 6:
Contents 1 Introduction 13 Introduc
Page 7 and 8:
Contents Delivery Checklist 55 Inst
Page 9 and 10:
Contents Running the CEC Analysis 1
Page 11 and 12:
Contents 9 Parts and Materials for
Page 13 and 14: Agilent 7100 Capillary Electrophore
Page 15 and 16: Introduction 1 Where to Find Inform
Page 19 and 20: Site Requirements and Specification
Page 55 and 56: Installing the Instrument 3 Unpacki
Page 57 and 58: Installing the Instrument 3 Install
Page 59 and 60: Installing the Instrument 3 Install
Page 63: LAN Configuration 4 TCP/IP Paramete
Page 67 and 68: LAN Configuration 4 Initialization
Page 69 and 70: LAN Configuration 4 Link Configurat
Page 71 and 72: LAN Configuration 4 Manual Configur
Page 73 and 74: LAN Configuration 4 Manual Configur
Page 75 and 76: LAN Configuration 4 Agilent Bootp S
Page 79 and 80: Controlling the Agilent CE Instrume
Page 81 and 82: Using the Agilent 7100 Capillary El
Page 115 and 116:
Using the Agilent 7100 Capillary El
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Troubleshooting and Diagnostics 6 C
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Troubleshooting and Diagnostics 6 A
Page 171 and 172:
Page 173 and 174:
Hardware Information 7 7100 Capilla
Page 175 and 176:
Hardware Information 7 7100 Capilla
Page 177 and 178:
Hardware Information 7 Firmware Fir
Page 179 and 180:
Hardware Information 7 Diode Array
Page 181 and 182:
Hardware Information 7 Diode Array
Page 183 and 184:
Hardware Information 7 Installing D
Page 185 and 186:
Hardware Information 7 External Wat
Page 187 and 188:
Hardware Information 7 Analog to Di
Page 189 and 190:
Page 191 and 192:
Maintenance 8 Overview of Maintenan
Page 193 and 194:
Maintenance 8 Overview of Maintenan
Page 195 and 196:
Maintenance 8 Early Maintenance Fee
Page 197 and 198:
Maintenance 8 Cleaning the Electrod
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Maintenance 8 Maintenance of the Re
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Maintenance 8 Changing the Air Inle
Page 225 and 226:
Maintenance 8 Changing the Lamp Rem
Page 227 and 228:
Maintenance 8 Changing the Lamp Ins
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Appendix 10 General Safety Informat
Page 235 and 236:
Appendix 10 Allgemeine Sicherheitsi
Page 237 and 238:
Appendix 10 Allgemeine Sicherheitsi
Page 239 and 240:
Appendix 10 Informations générale
Page 241 and 242:
Appendix 10 Informazioni generali s
Page 243 and 244:
Appendix 10 Informazioni generali s
Page 245 and 246:
Appendix 10 Información de segurid
Page 247 and 248:
Appendix 10 安全に関する
Page 249 and 250:
Appendix 10 安全に関する
Page 251 and 252:
Appendix 10 一般安全信息
Page 253 and 254:
Appendix 10 Setting Up a Test Sampl
Page 255 and 256:
Appendix 10 Setting Up a Test Sampl
Page 257 and 258:
Appendix 10 The Waste Electrical an
Page 259 and 260:
Appendix 10 Sound Emission Sound Em
Page 261 and 262:
Appendix 10 Agilent Technologies on
Page 263 and 264:
Index A accessing 199 accessories 5
Page 266:
www.agilent.com In This Book This m
show all

Introduction to the Agilent 7100 Capillary Electrophoresis System

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?