Catalyst 3750-E and 3560-E Switch Cisco IOS ... - DNIP . NET

diagnostic startChapter 2Catalyst 3750-E and 3560-E Switch Cisco IOS CommandsWhen specifying a test name, use the show diagnostic content privileged EXEC command to displaythe test ID list. To specify test 3 by using the test name, enter the diagnostic start switch number testTestPortAsicCam privileged EXEC command.If specifying more than one test to run, use the test-id-range parameter, and enter integers separated bya comma and a hyphen. For example, to specify tests 2, 3, and 4, enter the diagnostic start switchnumber test 2-4 command. To specify tests 1, 3, 4, 5, and 6, enter the diagnostic start switch numbertest 1,3-6 command.After starting the tests by using the diagnostic start command, you cannot stop the testing process.ExamplesThis example shows how to start diagnostic test 1 on stack member 2 when this command is entered on astack master:Switch# diagnostic start switch 2 test 1Switch#06:27:50: %DIAG-6-TEST_RUNNING: Switch 2: Running TestPortAsicStackPortLoopback{ID=1} ...(switch-1)06:27:51: %DIAG-6-TEST_OK: Switch 2: TestPortAsicStackPortLoopback{ID=1} has completedsuccessfully (switch-2)This example shows how to start diagnostic test 2 on a stack member in a switch stack. Running this testdisrupts the normal system operation, causes the switch to lose stack connectivity, and then causes theswitch to reload.Switch# diagnostic start switch 1 test 2Switch 1: Running test(s) 2 will cause the switch under test to reload after completion ofthe test list.Switch 1: Running test(s) 2 may disrupt normal system operationDo you want to continue? [no]: ySwitch#16:43:29: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 2 has changed to state DOWN16:43:30: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 9 has changed to state DOWN16:43:30: %STACKMGR-4-SWITCH_REMOVED: Switch 1 has been REMOVED from the stackSwitch#16:44:35: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 2 has changed to state UP16:44:37: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 2 has changed to state UP16:44:45: %STACKMGR-4-SWITCH_ADDED: Switch 1 has been ADDED to the stack16:45:00: %STACKMGR-5-SWITCH_READY: Switch 1 is READY16:45:00: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state UP16:45:00: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state UP00:00:20: %STACKMGR-4-SWITCH_ADDED: Switch 1 has been ADDED to the stack (Switch-1)00:00:20: %STACKMGR-4-SWITCH_ADDED: Switch 2 has been ADDED to the stack (Switch-1)00:00:25: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan (Switch-1)00:00:29: %SYS-5-CONFIG_I: Configured from memory by console (Switch-1)00:00:29: %STACKMGR-5-SWITCH_READY: Switch 2 is READY (Switch-1)00:00:29: %STACKMGR-5-MASTER_READY: Master Switch 2 is READY (Switch-1)00:00:30: %STACKMGR-5-SWITCH_READY: Switch 1 is READY (Switch-1)00:00:30: %DIAG-6-TEST_RUNNING: Switch 1: Running TestPortAsicLoopback{ID=2} ...(Switch-1)00:00:30: %DIAG-6-TEST_OK: Switch 1: TestPortAsicLoopback{ID=2} has completed successfully(Switch-1)This message appears if the configured test can cause the switch to lose stack connectivity:Switch 3: Running test(s) 2 will cause the switch under test to reload after completion ofthe test list.Switch 3: Running test(s) 2 may disrupt normal system operationDo you want to continue? [no]:2-144Catalyst 3750-E and 3560-E Switch Command ReferenceOL-9776-08