GMC-SG001E-EN-P-JUN01 Motion Control Selection Guide

6-48 Motors
Motor Dimensions
The following section contains the dimensions for the N-Series motors.
N-2300 Motors Dimensions
Figure 6.15
N-2300 Servo Motors Dimensions (N-230x-x-x0xAA)
L
LB
S is the diameter of the hole.
SS is the diameter of the bolt circle.
D
H
LL1
LD
T
EC
LC1
M
AB
Note: LC1 , LD and LL1
are shown on pg. 6-49.
N-3400, -4200 and -5600 Motors Dimensions
Figure 6.16
N-3400, -4200 and -5600 Servo Motors Dimensions (N-xxxx-x-x0xAA)
LB
L
EC
L-LB
EA
R
AB
M
D
H
LL2
LC2
T
S is the diameter of the hole.
SS is the diameter of the bolt circle.
Note: R = Width x Depth
Note: LC2 and LD2 are
shown on pg. 6-49.
Motor
AB
mm (in.)
D
mm (in.)
EA
mm (in.)
EC
mm (in.)
H
mm (in.)
L
mm (in.)
L with
brake
mm (in.)
LB
mm (in.)
L-LB
mm (in.)
M
mm (in.)
R
mm x
mm
(in. x in.)
S
mm (in.)
SS
mm (in.)
T
mm (in.)
N-2302
57.66
(2.27)
6.35
(0.25) 3 –
6.98
(0.27)
69.85
(2.75)
138.27
(5.44)
161.3
(6.35)
117.7
(4.63)
20.57
(0.81) 1 38.1
(1.5) 2 –
5.2
(0.2)
66.67
(2.62)
2.29
(0.09)
N-2304
57.66
(2.27)
6.35
(0.25) 3 –
6.985
(0.27)
69.85
(2.75)
176.37
(6.94)
199.4
(7.8)
155.8
(6.13)
20.57 38.1
(0.81) 1 (1.5) 2 –
5.2
(0.2)
66.67
(2.62)
2.29
(0.09)
N-3406
88.4
(3.48)
12.7 19.05 8
(0.5) 3 (0.75) 6 (0.31)
62.99
(2.48)
174.25
(6.86)
192.8
(7.6)
144.02
(5.67)
3.17 x 2
30.23 73.02
(1.19) 1 (2.87) 4 (0.125 x
5.59
0.085) 5 (0.22)
98.42
(3.87)
3.05
(0.12)
N-3412
88.4
(3.48)
12.7 19 8
(0.5) 3 (0.75) 6 (0.31)
62.9
(2.48)
199.65
(7.86)
218.19
(8.59)
169.42
(6.67)
3.17 x 2
30.23 73.02
(1.19) 1 (2.87) 4 (0.125 x
5.59
0.085) 5 (0.22)
98.42
(3.87)
3.05
(0.12)
Publication GMC-SG001E-EN-P — June 2001