Tsunami - Beckman Institute Laser Resource Center

More documents

Recommendations

Info

Tsunami Using needle-nose pliers, gently grasp the pc board and pull it out and from side to side to remove it from the module. - 3. Select the voltage. There are four voltage selections, one written on each edge of the pc board with a small arrow pointing to it. a. Measure your facility outlet voltage, then rotate the pc board until the edge with the measured voltage printed on it faces the inside of the module (the arrow points into the module). b. Move the white indicator pin in the pc board slot so it points away from your selection and so it will protrude through the correct hole in the cover plate when the plate is replaced in step 6. 4. Replace the voltage selector card. Make sure the pc board seats properly for good electrical contact. 5. Verify the correct fuse is installed. Remove the small screw holding the fuse block to the cover plate to access the fuse. Use the table below to determine the correct fuse size for your facility line voltage, then verify the correct one is installed. I Line Voltage Fuse Value 100 to 120 Vac 1 A slow blow 220 to 240 V, A slow blow 6. Snap the cover plate into place. If the indicator pin is not in the correct position, repeat steps 3 and 4. This completes the procedure for changing the voltage setting. I "
Appendix D Material Safetv Data Sheets This section contains scanned copies of material safety data sheets (MSDS) that are supplied by the vendor and cover the various chemicals and compounds used in the Tsunami laser system, i.e., the compounds used in the filters in the Model 3910 filterlpurge unit. DANGER Read the MSDS sheets carefully before handling or disposing of filter elements. They may contain hazardous chemicals. Spectra-Physics Lasers has not independently determined the accuracy of the Material Safety Data Sheets, which were developed by the manufacturer of each chemical; therefore, we do not warrant the information contained therein. Dispose of these filter elements properly as indicated on the appropriate data sheet, and refer to your local environmental regulations regarding disposal. For further information, contact the chemical manufacturer at the address listed on each sheet.
Page 1:
Tsunami Mode-locked Ti: sapphire La
Page 5 and 6:
Table of Contents ... Preface .....
Page 7 and 8:
Table of Contents . Chapter 6: Alig
Page 9 and 10:
Table of Contents Chapter 10: Optio
Page 11 and 12:
Table of Contents Figure 4-7: Typic
Page 13 and 14:
Table of Contents Figure A-6: The f
Page 15:
Warning Conventions The following w
Page 19:
List of Abbreviations Used in this
Page 22 and 23:
Tsunami Figure 1-1: The Tsunami Las
Page 25 and 26:
Chapter 2 Laser Safety DANGER The T
Page 27 and 28:
Laser Safety CA UTlON Use of contro
Page 29 and 30:
1 1 1 Il I 11 I I 1 El l11111II~Ill
Page 31 and 32:
Chapter 3 Laser Description General
Page 33 and 34:
Laser Description growth techniques
Page 35 and 36:
Laser Description - AOM OC n Fast P
Page 37 and 38:
Laser Description 2.4 - 2.2 - 2.0 -
Page 39 and 40:
I IIIIIN III I I 1 I 11111 i~ I I I
Page 41 and 42:
I II li I I I i 1 il I 1 11 I 1 1 1
Page 43:
I Laser Description . Outline Dimen
Page 46 and 47:
Tsunami Input Bezel Connections The
Page 48 and 49:
Tsunami Opto-Mechanical Controls Al
Page 50 and 51:
Tsunami Blue Knob: Vertical Adjust
Page 52 and 53:
~lpl~ f \ Tsunami Opto-Mechanical C
Page 54 and 55:
Tsunami Figure 4-7: 'Qpical MONITOR
Page 56 and 57:
Tsunami r @ Spectra-Physics - - 4 2
Page 58 and 59:
Tsunami Laser Installation Installi
Page 60 and 61:
Tsunami Setting up the Routing Mirr
Page 62 and 63:
Tsunami Aligning the Tsunami Laser
Page 64 and 65:
Tsunami A -----------. PHOTODIODE O
Page 66 and 67:
Tsunami Removing the Purge Line fro
Page 68 and 69:
Tsunami Motorized Mount "Dm-shaped
Page 70 and 71:
Tsunami I I J3 3930 - - - #,-,I --J
Page 72 and 73:
Tsunami CA UTION DO NOT remove or a
Page 74 and 75:
Tsunami Refer to the tables at the
Page 76 and 77:
Tsunami b. Move the stage by hand a
Page 78 and 79:
Tsunami There will be one or two re
Page 80 and 81:
Tsunami Figure 6-9: The Slit Contro
Page 82 and 83:
Tsunami b. Place a white card with
Page 84 and 85:
Tsunami Aligning the Photodiode PC
Page 86 and 87:
Tsunami To measure pulses, use a Sp
Page 88 and 89:
Tsunami pulses, adjust the coarse c
Page 90 and 91:
Tsunami Selecting, Installing, and
Page 92 and 93:
Tsunami Unless you are certain the
Page 94 and 95:
Tsunami Prism Translation Adjust Fi
Page 96 and 97:
Tsunami i. Route the GTI heater cab
Page 98 and 99:
Tsunami Figure 6-18: Pr1/Pr4 prisms
Page 100 and 101:
Tsunami Converting Between fs and p
Page 102 and 103:
Tsunami b. Using an ir viewer, adju
Page 104 and 105:
Tsunami g. Open the shutter. 15. Al
Page 106 and 107:
Tsunami 10. Move Prl and Pr4 into t
Page 108 and 109:
Tsunami 21. Mode lock Tsunami. Refe
Page 110 and 111:
I " n 3 1 ' ! ' I . I 8 8 8 " t 8 0
Page 112 and 113:
Tsunami recommend using 99.999% pur
Page 114 and 115:
Tsunami Mode Locking the Laser 6. W
Page 116 and 117:
Tsunami - - - 710 nrn - - 790 nrn -
Page 118 and 119:
4 Tsunami Beam % 2 mm (0.08 in.) Pr
Page 120 and 121:
Tsunami Table 7-1: Bi-fi Selection
Page 123 and 124:
I I1 ! I : I I I ill 8 I !Il! I1I l
Page 125 and 126:
Lok-to-Clock Electronics LEVEL cont
Page 127 and 128:
Lok-to-Clock Electronics AOM M5f-4
Page 129 and 130:
Lok-to-Clock Electronics Installing
Page 131 and 132:
I I1 I i l l I iil 111 ,111 Ill ,il
Page 133 and 134:
P Lok-to-Clock Electronics Model 20
Page 135 and 136:
I 1 1 I 1~~~ 11 I 1 1 1 1 .III :ill
Page 137 and 138:
Lok-to-Clock Electronics Figure 8-9
Page 139:
I I1 I l I 1 bll Lok-to-Clock Elect
Page 142 and 143:
Tsunami "Clean" is a relative descr
Page 144 and 145:
Tsunami Figure 9-1: Drop and Drag M
Page 146 and 147:
Tsunami With the exception of pump
Page 148 and 149:
Tsunami On rare occasions, the lowe
Page 150 and 151:
Tsunami 8. Open the pump laser shut
Page 152 and 153:
Tsunami 7. Remove the screws (4) ho
Page 154 and 155: Tsunami DryJClean Flow Adjust Nitro
Page 156 and 157: Tsunami diode such as the Model 393
Page 158 and 159: €968-PEP0 ES68-PEP0 PS68-PEP0 ES6
Page 160 and 161: Tsunami Check marks indicate which
Page 162 and 163: Tsunami Table 10-11: GTI and Bi-Pi
Page 164 and 165: Tsunami Generic Troubleshooting (No
Page 166 and 167: Tsunami Symptom: Laser will not mod
Page 168 and 169: Tsunami Symptom: Unable to mode loc
Page 170 and 171: Tsunami Symptom: Unable to mode loc
Page 172 and 173: Tsunami Symptom: Cannot see individ
Page 174 and 175: Tsunami Symptom: PZT oscillates whe
Page 177 and 178: I I ill ; I l l I I lll.l1 I I I *
Page 179 and 180: I I 111 il I iil i lllill ll I I ll
Page 181 and 182: I I il : I I I 1 I Appendix A Mode
Page 183 and 184: Mode Locking is chosen to be the sa
Page 185 and 186: I I 0 I I 1 I )I Ulllllll ill I Mod
Page 187 and 188: Mode Locking SPM will, thus, broade
Page 189 and 190: Mode Locking The net intracavity GV
Page 191 and 192: Appendix B Pulse Width Measurement
Page 193 and 194: I I 0 I I 1 1 LI I lillll Ill I!,ll
Page 195 and 196: Pulse Width Measurement -% GVD Comp
Page 197 and 198: I I I I I I I I ti 911 I1 I Pulse W
Page 199 and 200: I I I I I I B I IL 1 1 i 1111 I L I
Page 201 and 202: I I 0 I I 1 1 L I I Pulse Width Mea
Page 203: Appendix C Setting the Line Voltage
Page 207 and 208: Material Safety Data Sheets MATERIA
Page 209 and 210: I I I 1 r $1 I Bill II I I I I Ill
Page 211 and 212: Material Safety Data Sheets MATERIA
show all

Tsunami - Beckman Institute Laser Resource Center

Create successful ePaper yourself

Delete template?

Save as template?