9600 Service Manual - gmecorp-usa.com

More documents

Recommendations

Info

22 Mechanical Assemblies Figure 11 - Front Wheel Removal (Newer Style Cable Pushers)
Mechanical Assemblies 23 REAR WHEELS Rear Wheel Brake Adjustment CAUTION: Do not adjust the brake tension with the brake engaged (Lock Mode). 1. Release the brake. 2. Remove the hole plug. 3. With a Torx screwdriver, turn the Torx screw located in the caster, 1/4 turn counter clockwise to increase brake pressure. 4. Engage the brake and verify the adjustment was successful. Turn the Torx screw another 1/4 turn if necessary. Rear Caster Removal Surgi-glide II 1. Elevate and block the wheels approximately 2-1/2-inches off the floor. 2. Position the C-arm in the vertical position and engage the C-arm brake. Fully retract the C-arm through the cross arm housing and engage the cross arm brake. 3. Remove four 2-inch flathead Allen screws securing each wheel caster and end cap and remove both end caps. 4. Remove the 3 Allen head bolts located in each steering mode pedal and remove spring pins from each cam using a spring pin punch. 5. Slide the actuator shaft out of the brake housing of the caster assembly being replaced. Older Models This procedure was written for -01 version rear casters. Steps may vary slightly on -02 and -03 version rear casters. 1. Position the C-arm in the vertical position and engage the C-arm brake. Fully retract the C-arm through the cross arm housing and engage the cross arm brake. 2. Remove two 2-inch flathead Allen screws securing each wheel caster and end cap and remove both end caps. 3. Remove 2 Torx screws securing each cross beam cover and remove the cover. 4. Put the steering pedal in the LOCK (brake) position and then remove 5 of the 6 Allen head bolts located in the steering pedals and loosen the 6th. Loosen the 2 set screws in each cam by varying the position of the steering pedal. Place the steering pedal in the FREE position and remove the remaining Allen head bolt from the steering pedal. 5. Slide or tap the actuator shaft out of the brake housing of the caster assembly being replaced.
Page 1 and 2:
SERIES9600 SERVICE MANUAL © April
Page 3 and 4:
START-UP AND SOFTWARE BOOT Boot Seq
Page 5 and 6:
SRAM Card Error Codes If an error o
Page 7 and 8:
Event Codes & Messages The software
Page 9 and 10:
Event Codes & Messages (Cont.) CODE
Page 11 and 12:
Event Codes & Messages (Cont.) CODE
Page 13 and 14:
Event Codes & Messages (Cont.) 57 W
Page 15 and 16:
Low Battery Charge Messages Under m
Page 17 and 18:
Error Messages During Operation (Co
Page 19 and 20:
Status Menu Chart Use the following
Page 21 and 22:
PIO Status Use this menu to read th
Page 23 and 24:
Speaker Pitch This menu allows the
Page 25 and 26:
386 AMI BIOS Post Code Table These
Page 27 and 28:
386 AMI BIOS Post Code Table (Cont.
Page 29 and 30:
386 AMI BIOS Post Code Table (Cont.
Page 31 and 32:
Nobrk.com Error Codes (Executed by
Page 33 and 34:
Loadip.Exe (Executed By Autoexec.Ba
Page 35 and 36:
Critical Errors Fatal Errors Code D
Page 37 and 38:
ii 9600 System Service Manual © De
Page 39 and 40:
PURPOSE INTRODUCTION This manual co
Page 41 and 42:
Introduction 3 SAFETY PRECAUTIONS T
Page 43 and 44:
Introduction 5 EXPLOSION HAZARDS WA
Page 45 and 46:
Introduction 7 Dangerous Voltage Pr
Page 47 and 48:
Introduction 9 UNAUTHORIZED MODIFIC
Page 49 and 50:
OVERVIEW SYSTEM OVERVIEW This secti
Page 51 and 52:
System Overview 3 • Digital image
Page 53 and 54:
System Overview 5 • Auto and manu
Page 55 and 56:
System Overview 7 Video Monitors
Page 57 and 58:
System Overview 9 System Configurat
Page 59 and 60:
System Overview 11 NEUROVASCULAR MO
Page 61 and 62:
System Overview 13 SYSTEM OPERATION
Page 63 and 64:
System Overview 15 CAMERA ROTATION
Page 65 and 66:
System Overview 17 WORKSTATION CONT
Page 67 and 68:
System Overview 19 A V E R A G I N
Page 69 and 70:
System Overview 21 tab Ctrl Alt HEL
Page 71 and 72:
System Overview 23 Trackpad Panels
Page 73 and 74:
System Overview 25 Lenzar Hardcopy
Page 75 and 76:
System Overview 27 CONTROL PANEL WA
Page 77 and 78:
System Overview 29 WORKSTATION COVE
Page 79 and 80:
System Overview 31 3. Pull the left
Page 81 and 82:
System Overview 33 8. Remove the mo
Page 83 and 84:
System Overview 35 2. Grasp the top
Page 85 and 86:
System Overview 37 COMPONENT LOCATI
Page 87 and 88:
System Overview 39 Mobile C-Arm Com
Page 89 and 90:
System Overview 41 WORKSTATION COMP
Page 91 and 92:
System Overview 43 Power/Motor Rela
Page 93 and 94:
System Overview 45 IR Receiver PCB
Page 95 and 96:
OVERVIEW POWER DISTRIBUTION The inf
Page 97 and 98:
Power Distribution 3 WORKSTATION CI
Page 99 and 100:
Power Distribution 5 WORKSTATION IS
Page 101 and 102:
Power Distribution 7 POWER CONTROL
Page 103 and 104:
Power Distribution 9 CB1 CB2 CB3 Fi
Page 105 and 106:
Power Distribution 11 PS4 (+24 VDC)
Page 107 and 108:
Power Distribution 13 Figure 8 DC P
Page 109 and 110:
Power Distribution 15 PS1 (5V and 1
Page 111 and 112:
Power Distribution 17 115VAC_PH_SW
Page 113 and 114:
Power Distribution 19 120 VAC DC 7
Page 115 and 116:
Power Distribution 21 S/N 69-1001 a
Page 117 and 118:
Power Distribution 23 L N 1 L D 1 G
Page 119 and 120:
Power Distribution 25 PS2 (24V) S/N
Page 121 and 122:
Power Distribution 27 Current Sensi
Page 123 and 124:
Power Distribution 29 Battery Charg
Page 125 and 126:
Power Distribution 31 S/N 69-1001 a
Page 127 and 128:
Power Distribution 33 Battery Charg
Page 129 and 130:
Power Distribution 35 BATTERY RETAI
Page 131 and 132:
2 C-Arm Control • Mainframe Mothe
Page 133 and 134:
4 C-Arm Control C-ARM CONTROL PANEL
Page 135 and 136:
6 C-Arm Control CONTROL PANEL PROCE
Page 137 and 138:
8 C-Arm Control X-RAY SWITCH The si
Page 139 and 140:
10 C-Arm Control This illustration
Page 141 and 142:
12 C-Arm Control 3 C 5 U E5 U1 TP1
Page 143 and 144:
14 C-Arm Control CARD RACK ASSEMBLI
Page 145 and 146:
16 C-Arm Control TECHNIQUE PROCESSO
Page 147 and 148:
18 C-Arm Control 7-Segment Displays
Page 149 and 150:
20 C-Arm Control ANALOG INTERFACE P
Page 151 and 152:
22 C-Arm Control X U 4 8 X U 2 0 X
Page 153 and 154:
24 C-Arm Control A/D SECTION The A/
Page 155 and 156:
26 C-Arm Control COUNTER/TIMER (CTC
Page 157 and 158:
28 C-Arm Control BIT # PIN # SIGNAL
Page 159 and 160:
30 C-Arm Control INTERLOCK SECTION
Page 161 and 162:
32 C-Arm Control C-ARM MOTHERBOARD
Page 163 and 164:
34 C-Arm Control 3 E 1 R V 1 L F 8
Page 165 and 166:
36 C-Arm Control Technique Processo
Page 167 and 168:
38 C-Arm Control COMMUNICATION BETW
Page 169 and 170:
2 C-Arm Software LOADING APPLICATIO
Page 171 and 172:
4 C-Arm Software BOOT SEQUENCE Duri
Page 173 and 174:
6 C-Arm Software X-RAY CONTROL PANE
Page 175 and 176:
8 C-Arm Software A - Run Applicatio
Page 177 and 178:
10 C-Arm Software C - Run Calibrati
Page 179 and 180:
12 C-Arm Software H - Collimator Ca
Page 181 and 182:
14 C-Arm Software SRAM FILES The fo
Page 183 and 184:
16 C-Arm Software SRAM CARD COPY FI
Page 185 and 186:
18 C-Arm Software HOT-BYTE INFORMAT
Page 187 and 188:
20 C-Arm Software SRAM BATTERY REPL
Page 189 and 190:
2 Interlocks / Stator Power Signal
Page 191 and 192:
4 Interlocks / Stator FAST STOP The
Page 193 and 194:
6 Interlocks / Stator JUMPER E5/REL
Page 195 and 196:
8 Interlocks / Stator NORMAL PRE-CH
Page 197 and 198:
10 Interlocks / Stator STATOR START
Page 199 and 200:
12 Interlocks / Stator BATTERY CHAR
Page 201 and 202:
14 Interlocks / Stator POWER SUPPLY
Page 203 and 204:
OVERVIEW This section describes the
Page 205 and 206:
X-ray On / Disable 3 X-RAY ENABLE S
Page 207 and 208:
X-ray On / Disable 5 X-RAY DISABLE
Page 209 and 210:
OVERVIEW KV GENERATION kV is regula
Page 211 and 212:
kV Generation 3 The return path for
Page 213 and 214:
kV Generation 5 KV ERROR CORRECTION
Page 215 and 216:
kV Generation 7 Figure 3 kV Servo C
Page 217 and 218:
kV Generation 9 KV GENERATOR FAULTS
Page 219 and 220:
kV Generation 11 NOTE If the second
Page 221 and 222:
kV Generation 13 KV ERROR CORRECTIO
Page 223 and 224:
2 mA Generation CONTROL INPUTS The
Page 225 and 226:
4 mA Generation FILAMENT REGULATOR
Page 227 and 228:
6 mA Generation MA SENSE Detects th
Page 229 and 230:
8 mA Generation MA ERROR LOOP EXAMP
Page 231 and 232:
10 mA Generation Figure 2 - mA Serv
Page 233 and 234:
12 mA Generation LOW FLUORO MA The
Page 235 and 236:
14 mA Generation MA ERROR CORRECTIO
Page 237 and 238:
2 Generator Calibration During the
Page 239 and 240:
4 Generator Calibration CALIBRATION
Page 241 and 242:
6 Generator Calibration EQUIPMENT S
Page 243 and 244: 8 Generator Calibration 11. Observi
Page 245 and 246: 10 Generator Calibration mA ZERO R
Page 247 and 248: 12 Generator Calibration ACCESS CAL
Page 249 and 250: 14 Generator Calibration DUTY CYCLE
Page 251 and 252: 16 Generator Calibration KV/MA TECH
Page 253 and 254: 18 Generator Calibration MERGE EXIS
Page 255 and 256: 20 Generator Calibration 5R THEORY
Page 257 and 258: 22 Generator Calibration Example 3
Page 259 and 260: 24 Generator Calibration 5R ABS TAB
Page 261 and 262: 26 Generator Calibration 3. Increas
Page 263 and 264: 28 Generator Calibration NOTE: You
Page 265 and 266: 30 Generator Calibration B. mA limi
Page 267 and 268: 32 Generator Calibration 19. Withou
Page 269 and 270: 34 Generator Calibration 10R ABS TA
Page 271 and 272: 36 Generator Calibration 10R ENTRAN
Page 273 and 274: OVERVIEW MECHANICAL ASSEMBLIES The
Page 275 and 276: Mechanical Assemblies 3 HORIZONTAL
Page 277 and 278: Mechanical Assemblies 5 MECHANICAL
Page 279 and 280: Mechanical Assemblies 7 HORIZONTAL
Page 281 and 282: Mechanical Assemblies 9 Figure 5 -
Page 283 and 284: Mechanical Assemblies 11 FLIP FLOP
Page 285 and 286: Mechanical Assemblies 13 C-ARM BEAR
Page 287 and 288: Mechanical Assemblies 15 WIG WAG BR
Page 289 and 290: Mechanical Assemblies 17 Figure 8 -
Page 291 and 292: Mechanical Assemblies 19 REAR CASTE
Page 293: Mechanical Assemblies 21 FRONT WHEE
Page 297 and 298: Mechanical Assemblies 25 Older Mode
Page 299 and 300: Mechanical Assemblies 27 Older Mode
Page 301 and 302: Mechanical Assemblies 29 Shim Adjus
Page 303 and 304: Mechanical Assemblies 31 L-ARM ROTA
Page 305 and 306: Mechanical Assemblies 33 CROSS ARM
Page 307 and 308: Mechanical Assemblies 35 Figure 16
Page 309 and 310: Mechanical Assemblies 37 VERTICAL C
Page 311 and 312: Mechanical Assemblies 39 3. Remove
Page 313 and 314: 2 Image System Mainframe Motherboar
Page 315 and 316: 4 Image System IMAGE FUNCTION PCB S
Page 317 and 318: 6 Image System ��
Page 319 and 320: 8 Image System COLLIMATOR OVERVIEW
Page 321 and 322: 10 Image System IRIS MOTOR The coll
Page 323 and 324: 12 Image System LEAF IN/OUT MOTOR T
Page 325 and 326: 14 Image System LEAF ROTATION MOTOR
Page 327 and 328: 16 Image System COLLIMATOR ERROR ME
Page 329 and 330: 18 Image System IMAGE INTENSIFIER O
Page 331 and 332: 20 Image System WARNING... Image in
Page 333 and 334: 22 Image System CCD CAMERA OVERVIEW
Page 335 and 336: 24 Image System Invert Image/ Rever
Page 341 and 342: 30 Image System Anti-Vignetting A s
Page 343 and 344: 32 Image System PIXEL/COLUMN FILTER
Page 345 and 346:
34 Image System PIXEL FILTER PCB As
Page 347 and 348:
36 Image System CCD CAMERA REPLACEM
Page 349 and 350:
38 Image System CCD CAMERA REPLACEM
Page 351 and 352:
40 Image System VIDEO LEVEL INDICAT
Page 353 and 354:
42 Image System ��
Page 355 and 356:
44 Image System STATOR THERMAL CUTO
Page 357 and 358:
46 Image System REPLACEMENT OF HIGH
Page 359 and 360:
IMAGE SYSTEM CALIBRATION The proced
Page 361 and 362:
Image System Calibration 3 TOOLS Th
Page 363 and 364:
Image System Calibration 5 4. Attac
Page 365 and 366:
Image System Calibration 7 CALIBRAT
Page 367 and 368:
Image System Calibration 9 10. With
Page 369 and 370:
Image System Calibration 11 CONFIRM
Page 371 and 372:
Image System Calibration 13 ADJUST
Page 373 and 374:
Image System Calibration 15 8. Sele
Page 375 and 376:
Image System Calibration 17 Figure
Page 377 and 378:
Image System Calibration 19 4. If t
Page 379 and 380:
Image System Calibration 21 270° 0
Page 381 and 382:
Image System Calibration 23 ADJUST
Page 383 and 384:
Image System Calibration 25 COLLIMA
Page 385 and 386:
Image System Calibration 27 NOTE: I
Page 387 and 388:
Image System Calibration 29 VARIABL
Page 389 and 390:
Image System Calibration 31 9. Sele
Page 391 and 392:
Image System Calibration 33 BEAM AL
Page 393 and 394:
Image System Calibration 35 C. Swin
Page 395 and 396:
Image System Calibration 37 Adjust
Page 397 and 398:
Image System Calibration 39 PIXEL/C
Page 399 and 400:
Image System Calibration 41 ANTI-VI
Page 401 and 402:
OVERVIEW WORKSTATION CONTROL This s
Page 403 and 404:
Workstation Control 3 CONTROL PANEL
Page 405 and 406:
Workstation Control 5 CONTROL PANEL
Page 407 and 408:
Workstation Control 7 Figure 3 - Wo
Page 409 and 410:
Workstation Control 9 ELECTRONICS B
Page 411 and 412:
Workstation Control 11 AUXILIARY IN
Page 413 and 414:
Workstation Control 13 X-RAY DISABL
Page 415 and 416:
Workstation Control 15 COMMUNICATIO
Page 417 and 418:
Workstation Control 17 OPTION PROM
Page 419 and 420:
Workstation Control 19 386 AT MOTHE
Page 421 and 422:
Workstation Control 21 IR (INFRARED
Page 423 and 424:
Workstation Control 23 If the pulse
Page 425 and 426:
Workstation Control 25 IR RECEIVER
Page 427 and 428:
Workstation Control 27 Older Style
Page 429 and 430:
Workstation Control 29 INTERCONNECT
Page 431 and 432:
2 Workstation Software WORKSTATION
Page 433 and 434:
4 Workstation Software FRONT PANEL
Page 435 and 436:
6 Workstation Software TOGGLE MOTIO
Page 437 and 438:
8 Workstation Software Qwerty Keys
Page 439 and 440:
10 Workstation Software Track Pad K
Page 441 and 442:
12 Workstation Software Front Panel
Page 443 and 444:
14 Workstation Software Tone Contro
Page 445 and 446:
16 Workstation Software Watchdog Re
Page 447 and 448:
Video Path 2 REFERENCE SCHEMATICS T
Page 449 and 450:
Video Path 4 HIGH SCAN NON INTERLAC
Page 451 and 452:
Video Path 6 WORKSTATION The video
Page 453 and 454:
Video Path 8 Auxiliary Interface PC
Page 455 and 456:
Video Path 10 Peripherals Analog in
Page 457 and 458:
Video Path 12 HARD COPY CAMERA Vide
Page 459 and 460:
Video Path 14 Auxiliary Interface P
Page 461 and 462:
Video Path 16 Video Switching PCB O
Page 463 and 464:
Video Path 18 Scan Converter PCB Fi
Page 465 and 466:
2 Video Control IMAGE PROCESSOR PCB
Page 467 and 468:
4 Video Control IMAGE PROCESSOR TES
Page 469 and 470:
6 Video Control VIDEO SWITCHING PCB
Page 471 and 472:
8 Video Control 50/60 HZ VIDEO CONT
Page 473 and 474:
10 Video Control FAST SCAN MONITORS
Page 475 and 476:
12 Video Control CONTRAST AND BRIGH
Page 477 and 478:
14 Video Control HIGH SCAN BRIGHTNE
Page 479 and 480:
2 Image Storage IDE HARD DISK DRIVE
Page 481 and 482:
4 Image Storage 30FPS SCSI DISK OPT
Page 483 and 484:
6 Image Storage 4/30 FPS SCSI DISK
Page 485 and 486:
8 Image Storage 14. The following w
Page 487 and 488:
Image Storage DEBUGGING USING IP-SC
Page 489 and 490:
12 Image Storage ��
Page 491 and 492:
14 Image Storage Figure 7 - SCSI Di
Page 493 and 494:
16 Image Storage Figure 9 - IP-SCSI
Page 495 and 496:
18 Image Storage � � � �
Page 497 and 498:
20 Image Storage ��
Page 499 and 500:
2 Peripherals Figure 1 - Rear Panel
Page 501 and 502:
4 Peripherals RECORD UNPROCESSED VI
Page 503 and 504:
6 Peripherals VCR CONNECTIONS To en
Page 505 and 506:
8 Peripherals HARD COPY CAMERA Imag
Page 507 and 508:
10 Peripherals MOUNTING INFORMATION
Page 509 and 510:
12 Peripherals DIGITAL LASER CAMERA
Page 511 and 512:
14 Peripherals 6. When CUSTOMIZE OP
Page 513 and 514:
16 Peripherals Digital Laser Camera
Page 515 and 516:
18 Peripherals After the unit has b
Page 517 and 518:
20 Peripherals 3. Then, select a sp
Page 519 and 520:
22 Peripherals 4. Move the cursor t
Page 521 and 522:
2 Appendix PAINT KITS PART NUMBER D
Page 523 and 524:
4 Appendix SPECIFICATIONS & TOLERAN
Page 525 and 526:
UPDATE 12-INCH IMAGE SYSTEM 9600 SY
Page 527 and 528:
00 Imaging Workstation Service Manu
Page 529 and 530:
9600 Imaging Workstation Service Ma
Page 531 and 532:
Page 533 and 534:
Page 535 and 536:
Page 537 and 538:
Page 539 and 540:
Page 541 and 542:
Page 543 and 544:
Page 545 and 546:
show all

9600 Service Manual - gmecorp-usa.com

Create successful ePaper yourself

Delete template?

Save as template?