9600 Service Manual - gmecorp-usa.com

More documents

Recommendations

Info

10 System Overview • Variable edge enhancement (TrackPad) • Variable zoom & roam (TrackPad) • Patient directory with minified image scroll (TrackPad) • Anatomical markers • Procedural dose log (mA, kVp, time, patient) • Integrated S-VHS VCR (optional) • Multi-function infra-red remote control (optional) • 4 FPS digital disk (optional) DIGITAL SPOT (CHOLE) MODULE (OPTIONAL) Available only with the Expanded Surgical Platform (ESP) • Enhanced digital fluorographic one-shot with 12 mA boost • Automatically terminates exposure and stores enhanced image to 100 image storage archival disk • Digital laser camera interface, 3M 952 protocol (optional) • 4 FPS or 30 FPS digital disk (optional) VASCULAR MODULE (OPTIONAL) Available only with the Expanded Surgical Platform (ESP) • Continuous fluoro boost mode up to 12 mA • Pulsed Fluorography mode up to 40 mA • Real-time subtraction • Roadmapping • Peak opacification • Re-registration (TrackPad) • Variable landmarking (TrackPad) • Mask save/recall • Integrated S-VHS VCR (optional) • 4 fps digital disk (optional)
System Overview 11 NEUROVASCULAR MODULE (OPTIONAL) Available only with the Expanded Surgical Platform (ESP) • Continuous fluoro boost mode up to 12 mA • Pulsed fluorography mode up to 40 mA • Real-time subtraction • Roadmapping • Peak opacification • Re-registration (TrackPad) • Variable landmarking (TrackPad) • Mask save/recall • Integrated S-VHS VCR (optional) • 30 FPS digital disk • Record/play rate: 1, 2, 4, 8, 15 or 30 fps • Record time: 150, 75, 40, 20, 10 or 5 minutes • Image storage: 9,000 digital images (60 Hz) • Instant image access with TrackPad • Synchronized to pulse with generator, CCD camera and image processor 4 FRAMES/SECOND DIGITAL DISK (OPTIONAL) Available only with the Expanded Surgical Platform (ESP), Digital Spot (Chole) or Vascular Modules • Record/play rate: 1, 2 or 4 FPS • Record time: 22, 11 or 6 minutes • Image storage: 1,350 digital images (60 Hz) • Instant image access with TrackPad • Synchronized to pulse with generator, CCD camera and image processor
Page 1 and 2:
SERIES9600 SERVICE MANUAL © April
Page 3 and 4:
START-UP AND SOFTWARE BOOT Boot Seq
Page 5 and 6:
SRAM Card Error Codes If an error o
Page 7 and 8: Event Codes & Messages The software
Page 9 and 10: Event Codes & Messages (Cont.) CODE
Page 11 and 12: Event Codes & Messages (Cont.) CODE
Page 13 and 14: Event Codes & Messages (Cont.) 57 W
Page 15 and 16: Low Battery Charge Messages Under m
Page 17 and 18: Error Messages During Operation (Co
Page 19 and 20: Status Menu Chart Use the following
Page 21 and 22: PIO Status Use this menu to read th
Page 23 and 24: Speaker Pitch This menu allows the
Page 25 and 26: 386 AMI BIOS Post Code Table These
Page 27 and 28: 386 AMI BIOS Post Code Table (Cont.
Page 29 and 30: 386 AMI BIOS Post Code Table (Cont.
Page 31 and 32: Nobrk.com Error Codes (Executed by
Page 33 and 34: Loadip.Exe (Executed By Autoexec.Ba
Page 35 and 36: Critical Errors Fatal Errors Code D
Page 37 and 38: ii 9600 System Service Manual © De
Page 39 and 40: PURPOSE INTRODUCTION This manual co
Page 41 and 42: Introduction 3 SAFETY PRECAUTIONS T
Page 43 and 44: Introduction 5 EXPLOSION HAZARDS WA
Page 45 and 46: Introduction 7 Dangerous Voltage Pr
Page 47 and 48: Introduction 9 UNAUTHORIZED MODIFIC
Page 49 and 50: OVERVIEW SYSTEM OVERVIEW This secti
Page 51 and 52: System Overview 3 • Digital image
Page 53 and 54: System Overview 5 • Auto and manu
Page 55 and 56: System Overview 7 Video Monitors
Page 57: System Overview 9 System Configurat
Page 61 and 62: System Overview 13 SYSTEM OPERATION
Page 63 and 64: System Overview 15 CAMERA ROTATION
Page 65 and 66: System Overview 17 WORKSTATION CONT
Page 67 and 68: System Overview 19 A V E R A G I N
Page 69 and 70: System Overview 21 tab Ctrl Alt HEL
Page 71 and 72: System Overview 23 Trackpad Panels
Page 73 and 74: System Overview 25 Lenzar Hardcopy
Page 75 and 76: System Overview 27 CONTROL PANEL WA
Page 77 and 78: System Overview 29 WORKSTATION COVE
Page 79 and 80: System Overview 31 3. Pull the left
Page 81 and 82: System Overview 33 8. Remove the mo
Page 83 and 84: System Overview 35 2. Grasp the top
Page 85 and 86: System Overview 37 COMPONENT LOCATI
Page 87 and 88: System Overview 39 Mobile C-Arm Com
Page 89 and 90: System Overview 41 WORKSTATION COMP
Page 91 and 92: System Overview 43 Power/Motor Rela
Page 93 and 94: System Overview 45 IR Receiver PCB
Page 95 and 96: OVERVIEW POWER DISTRIBUTION The inf
Page 97 and 98: Power Distribution 3 WORKSTATION CI
Page 99 and 100: Power Distribution 5 WORKSTATION IS
Page 101 and 102: Power Distribution 7 POWER CONTROL
Page 103 and 104: Power Distribution 9 CB1 CB2 CB3 Fi
Page 105 and 106: Power Distribution 11 PS4 (+24 VDC)
Page 107 and 108: Power Distribution 13 Figure 8 DC P
Page 109 and 110:
Power Distribution 15 PS1 (5V and 1
Page 111 and 112:
Power Distribution 17 115VAC_PH_SW
Page 113 and 114:
Power Distribution 19 120 VAC DC 7
Page 115 and 116:
Power Distribution 21 S/N 69-1001 a
Page 117 and 118:
Power Distribution 23 L N 1 L D 1 G
Page 119 and 120:
Power Distribution 25 PS2 (24V) S/N
Page 121 and 122:
Power Distribution 27 Current Sensi
Page 123 and 124:
Power Distribution 29 Battery Charg
Page 125 and 126:
Power Distribution 31 S/N 69-1001 a
Page 127 and 128:
Power Distribution 33 Battery Charg
Page 129 and 130:
Power Distribution 35 BATTERY RETAI
Page 131 and 132:
2 C-Arm Control • Mainframe Mothe
Page 133 and 134:
4 C-Arm Control C-ARM CONTROL PANEL
Page 135 and 136:
6 C-Arm Control CONTROL PANEL PROCE
Page 137 and 138:
8 C-Arm Control X-RAY SWITCH The si
Page 139 and 140:
10 C-Arm Control This illustration
Page 141 and 142:
12 C-Arm Control 3 C 5 U E5 U1 TP1
Page 143 and 144:
14 C-Arm Control CARD RACK ASSEMBLI
Page 145 and 146:
16 C-Arm Control TECHNIQUE PROCESSO
Page 147 and 148:
18 C-Arm Control 7-Segment Displays
Page 149 and 150:
20 C-Arm Control ANALOG INTERFACE P
Page 151 and 152:
22 C-Arm Control X U 4 8 X U 2 0 X
Page 153 and 154:
24 C-Arm Control A/D SECTION The A/
Page 155 and 156:
26 C-Arm Control COUNTER/TIMER (CTC
Page 157 and 158:
28 C-Arm Control BIT # PIN # SIGNAL
Page 159 and 160:
30 C-Arm Control INTERLOCK SECTION
Page 161 and 162:
32 C-Arm Control C-ARM MOTHERBOARD
Page 163 and 164:
34 C-Arm Control 3 E 1 R V 1 L F 8
Page 165 and 166:
36 C-Arm Control Technique Processo
Page 167 and 168:
38 C-Arm Control COMMUNICATION BETW
Page 169 and 170:
2 C-Arm Software LOADING APPLICATIO
Page 171 and 172:
4 C-Arm Software BOOT SEQUENCE Duri
Page 173 and 174:
6 C-Arm Software X-RAY CONTROL PANE
Page 175 and 176:
8 C-Arm Software A - Run Applicatio
Page 177 and 178:
10 C-Arm Software C - Run Calibrati
Page 179 and 180:
12 C-Arm Software H - Collimator Ca
Page 181 and 182:
14 C-Arm Software SRAM FILES The fo
Page 183 and 184:
16 C-Arm Software SRAM CARD COPY FI
Page 185 and 186:
18 C-Arm Software HOT-BYTE INFORMAT
Page 187 and 188:
20 C-Arm Software SRAM BATTERY REPL
Page 189 and 190:
2 Interlocks / Stator Power Signal
Page 191 and 192:
4 Interlocks / Stator FAST STOP The
Page 193 and 194:
6 Interlocks / Stator JUMPER E5/REL
Page 195 and 196:
8 Interlocks / Stator NORMAL PRE-CH
Page 197 and 198:
10 Interlocks / Stator STATOR START
Page 199 and 200:
12 Interlocks / Stator BATTERY CHAR
Page 201 and 202:
14 Interlocks / Stator POWER SUPPLY
Page 203 and 204:
OVERVIEW This section describes the
Page 205 and 206:
X-ray On / Disable 3 X-RAY ENABLE S
Page 207 and 208:
X-ray On / Disable 5 X-RAY DISABLE
Page 209 and 210:
OVERVIEW KV GENERATION kV is regula
Page 211 and 212:
kV Generation 3 The return path for
Page 213 and 214:
kV Generation 5 KV ERROR CORRECTION
Page 215 and 216:
kV Generation 7 Figure 3 kV Servo C
Page 217 and 218:
kV Generation 9 KV GENERATOR FAULTS
Page 219 and 220:
kV Generation 11 NOTE If the second
Page 221 and 222:
kV Generation 13 KV ERROR CORRECTIO
Page 223 and 224:
2 mA Generation CONTROL INPUTS The
Page 225 and 226:
4 mA Generation FILAMENT REGULATOR
Page 227 and 228:
6 mA Generation MA SENSE Detects th
Page 229 and 230:
8 mA Generation MA ERROR LOOP EXAMP
Page 231 and 232:
10 mA Generation Figure 2 - mA Serv
Page 233 and 234:
12 mA Generation LOW FLUORO MA The
Page 235 and 236:
14 mA Generation MA ERROR CORRECTIO
Page 237 and 238:
2 Generator Calibration During the
Page 239 and 240:
4 Generator Calibration CALIBRATION
Page 241 and 242:
6 Generator Calibration EQUIPMENT S
Page 243 and 244:
8 Generator Calibration 11. Observi
Page 245 and 246:
10 Generator Calibration mA ZERO R
Page 247 and 248:
12 Generator Calibration ACCESS CAL
Page 249 and 250:
14 Generator Calibration DUTY CYCLE
Page 251 and 252:
16 Generator Calibration KV/MA TECH
Page 253 and 254:
18 Generator Calibration MERGE EXIS
Page 255 and 256:
20 Generator Calibration 5R THEORY
Page 257 and 258:
22 Generator Calibration Example 3
Page 259 and 260:
24 Generator Calibration 5R ABS TAB
Page 261 and 262:
26 Generator Calibration 3. Increas
Page 263 and 264:
28 Generator Calibration NOTE: You
Page 265 and 266:
30 Generator Calibration B. mA limi
Page 267 and 268:
32 Generator Calibration 19. Withou
Page 269 and 270:
34 Generator Calibration 10R ABS TA
Page 271 and 272:
36 Generator Calibration 10R ENTRAN
Page 273 and 274:
OVERVIEW MECHANICAL ASSEMBLIES The
Page 275 and 276:
Mechanical Assemblies 3 HORIZONTAL
Page 277 and 278:
Mechanical Assemblies 5 MECHANICAL
Page 279 and 280:
Mechanical Assemblies 7 HORIZONTAL
Page 281 and 282:
Mechanical Assemblies 9 Figure 5 -
Page 283 and 284:
Mechanical Assemblies 11 FLIP FLOP
Page 285 and 286:
Mechanical Assemblies 13 C-ARM BEAR
Page 287 and 288:
Mechanical Assemblies 15 WIG WAG BR
Page 289 and 290:
Mechanical Assemblies 17 Figure 8 -
Page 291 and 292:
Mechanical Assemblies 19 REAR CASTE
Page 293 and 294:
Mechanical Assemblies 21 FRONT WHEE
Page 295 and 296:
Mechanical Assemblies 23 REAR WHEEL
Page 297 and 298:
Mechanical Assemblies 25 Older Mode
Page 299 and 300:
Mechanical Assemblies 27 Older Mode
Page 301 and 302:
Mechanical Assemblies 29 Shim Adjus
Page 303 and 304:
Mechanical Assemblies 31 L-ARM ROTA
Page 305 and 306:
Mechanical Assemblies 33 CROSS ARM
Page 307 and 308:
Mechanical Assemblies 35 Figure 16
Page 309 and 310:
Mechanical Assemblies 37 VERTICAL C
Page 311 and 312:
Mechanical Assemblies 39 3. Remove
Page 313 and 314:
2 Image System Mainframe Motherboar
Page 315 and 316:
4 Image System IMAGE FUNCTION PCB S
Page 317 and 318:
6 Image System ��
Page 319 and 320:
8 Image System COLLIMATOR OVERVIEW
Page 321 and 322:
10 Image System IRIS MOTOR The coll
Page 323 and 324:
12 Image System LEAF IN/OUT MOTOR T
Page 325 and 326:
14 Image System LEAF ROTATION MOTOR
Page 327 and 328:
16 Image System COLLIMATOR ERROR ME
Page 329 and 330:
18 Image System IMAGE INTENSIFIER O
Page 331 and 332:
20 Image System WARNING... Image in
Page 333 and 334:
22 Image System CCD CAMERA OVERVIEW
Page 335 and 336:
24 Image System Invert Image/ Rever
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
30 Image System Anti-Vignetting A s
Page 343 and 344:
32 Image System PIXEL/COLUMN FILTER
Page 345 and 346:
34 Image System PIXEL FILTER PCB As
Page 347 and 348:
36 Image System CCD CAMERA REPLACEM
Page 349 and 350:
38 Image System CCD CAMERA REPLACEM
Page 351 and 352:
40 Image System VIDEO LEVEL INDICAT
Page 353 and 354:
Page 355 and 356:
44 Image System STATOR THERMAL CUTO
Page 357 and 358:
46 Image System REPLACEMENT OF HIGH
Page 359 and 360:
IMAGE SYSTEM CALIBRATION The proced
Page 361 and 362:
Image System Calibration 3 TOOLS Th
Page 363 and 364:
Image System Calibration 5 4. Attac
Page 365 and 366:
Image System Calibration 7 CALIBRAT
Page 367 and 368:
Image System Calibration 9 10. With
Page 369 and 370:
Image System Calibration 11 CONFIRM
Page 371 and 372:
Image System Calibration 13 ADJUST
Page 373 and 374:
Image System Calibration 15 8. Sele
Page 375 and 376:
Image System Calibration 17 Figure
Page 377 and 378:
Image System Calibration 19 4. If t
Page 379 and 380:
Image System Calibration 21 270° 0
Page 381 and 382:
Image System Calibration 23 ADJUST
Page 383 and 384:
Image System Calibration 25 COLLIMA
Page 385 and 386:
Image System Calibration 27 NOTE: I
Page 387 and 388:
Image System Calibration 29 VARIABL
Page 389 and 390:
Image System Calibration 31 9. Sele
Page 391 and 392:
Image System Calibration 33 BEAM AL
Page 393 and 394:
Image System Calibration 35 C. Swin
Page 395 and 396:
Image System Calibration 37 Adjust
Page 397 and 398:
Image System Calibration 39 PIXEL/C
Page 399 and 400:
Image System Calibration 41 ANTI-VI
Page 401 and 402:
OVERVIEW WORKSTATION CONTROL This s
Page 403 and 404:
Workstation Control 3 CONTROL PANEL
Page 405 and 406:
Workstation Control 5 CONTROL PANEL
Page 407 and 408:
Workstation Control 7 Figure 3 - Wo
Page 409 and 410:
Workstation Control 9 ELECTRONICS B
Page 411 and 412:
Workstation Control 11 AUXILIARY IN
Page 413 and 414:
Workstation Control 13 X-RAY DISABL
Page 415 and 416:
Workstation Control 15 COMMUNICATIO
Page 417 and 418:
Workstation Control 17 OPTION PROM
Page 419 and 420:
Workstation Control 19 386 AT MOTHE
Page 421 and 422:
Workstation Control 21 IR (INFRARED
Page 423 and 424:
Workstation Control 23 If the pulse
Page 425 and 426:
Workstation Control 25 IR RECEIVER
Page 427 and 428:
Workstation Control 27 Older Style
Page 429 and 430:
Workstation Control 29 INTERCONNECT
Page 431 and 432:
2 Workstation Software WORKSTATION
Page 433 and 434:
4 Workstation Software FRONT PANEL
Page 435 and 436:
6 Workstation Software TOGGLE MOTIO
Page 437 and 438:
8 Workstation Software Qwerty Keys
Page 439 and 440:
10 Workstation Software Track Pad K
Page 441 and 442:
12 Workstation Software Front Panel
Page 443 and 444:
14 Workstation Software Tone Contro
Page 445 and 446:
16 Workstation Software Watchdog Re
Page 447 and 448:
Video Path 2 REFERENCE SCHEMATICS T
Page 449 and 450:
Video Path 4 HIGH SCAN NON INTERLAC
Page 451 and 452:
Video Path 6 WORKSTATION The video
Page 453 and 454:
Video Path 8 Auxiliary Interface PC
Page 455 and 456:
Video Path 10 Peripherals Analog in
Page 457 and 458:
Video Path 12 HARD COPY CAMERA Vide
Page 459 and 460:
Video Path 14 Auxiliary Interface P
Page 461 and 462:
Video Path 16 Video Switching PCB O
Page 463 and 464:
Video Path 18 Scan Converter PCB Fi
Page 465 and 466:
2 Video Control IMAGE PROCESSOR PCB
Page 467 and 468:
4 Video Control IMAGE PROCESSOR TES
Page 469 and 470:
6 Video Control VIDEO SWITCHING PCB
Page 471 and 472:
8 Video Control 50/60 HZ VIDEO CONT
Page 473 and 474:
10 Video Control FAST SCAN MONITORS
Page 475 and 476:
12 Video Control CONTRAST AND BRIGH
Page 477 and 478:
14 Video Control HIGH SCAN BRIGHTNE
Page 479 and 480:
2 Image Storage IDE HARD DISK DRIVE
Page 481 and 482:
4 Image Storage 30FPS SCSI DISK OPT
Page 483 and 484:
6 Image Storage 4/30 FPS SCSI DISK
Page 485 and 486:
8 Image Storage 14. The following w
Page 487 and 488:
Image Storage DEBUGGING USING IP-SC
Page 489 and 490:
12 Image Storage ��
Page 491 and 492:
14 Image Storage Figure 7 - SCSI Di
Page 493 and 494:
16 Image Storage Figure 9 - IP-SCSI
Page 495 and 496:
18 Image Storage � � � �
Page 497 and 498:
20 Image Storage ��
Page 499 and 500:
2 Peripherals Figure 1 - Rear Panel
Page 501 and 502:
4 Peripherals RECORD UNPROCESSED VI
Page 503 and 504:
6 Peripherals VCR CONNECTIONS To en
Page 505 and 506:
8 Peripherals HARD COPY CAMERA Imag
Page 507 and 508:
10 Peripherals MOUNTING INFORMATION
Page 509 and 510:
12 Peripherals DIGITAL LASER CAMERA
Page 511 and 512:
14 Peripherals 6. When CUSTOMIZE OP
Page 513 and 514:
16 Peripherals Digital Laser Camera
Page 515 and 516:
18 Peripherals After the unit has b
Page 517 and 518:
20 Peripherals 3. Then, select a sp
Page 519 and 520:
22 Peripherals 4. Move the cursor t
Page 521 and 522:
2 Appendix PAINT KITS PART NUMBER D
Page 523 and 524:
4 Appendix SPECIFICATIONS & TOLERAN
Page 525 and 526:
UPDATE 12-INCH IMAGE SYSTEM 9600 SY
Page 527 and 528:
00 Imaging Workstation Service Manu
Page 529 and 530:
9600 Imaging Workstation Service Ma
Page 531 and 532:
Page 533 and 534:
Page 535 and 536:
Page 537 and 538:
Page 539 and 540:
Page 541 and 542:
Page 543 and 544:
Page 545 and 546:
show all

9600 Service Manual - gmecorp-usa.com

Create successful ePaper yourself

Delete template?

Save as template?