Pneumatic Clean Series

Solenoid Valve 10-SY3000/5000/7000290CautionBe sure to read before handling.Refer to pages 7 to 16 of Frontmatter for safety instructions andcommon precautions for cleanseries and pages 236 to 238 forcommon precautions fordirectional control valve.SpecificationsSeries10-SY3000 10-SY5000 10-SY7000FluidAirInternal pilotoperating pressure rangeMPa2 position single2 position double3 position0.15 to 0.70.1 to 0.70.2 to 0.7Operating pressure range–100kPa to 0.7External pilotPilot 2 position single0.25 to 0.7operating pressure rangepressureMPa2 position double0.25 to 0.7range 3 position0.25 to 0.7Ambient and fluid temperature °CMax. 50Maximum operatingfrequency Hz2 position single, double3 position1035353Manual overridePilot exhaust methodNon-locking push type,Push-turn locking push type, Push-turn locking lever typeInternal pilotCommon exhaust (Pilot and main valve)External pilotIndividual pilot exhaustLubricationNot requiredMounting orientationFreeNote) Shock resistance/vibration resistance m/s 2Enclosure150/30Dust proof (∗DIN connector IP65)∗According to IEC529Note) Impact resistance: No malfunction resulted in an impact test using a drop impact tester.The test was performed in the axial and right angle directions of the main valve andarmature, for both energized and deenergized states. (Value in the initial stage).Vibration resistance: No malfunction resulted in a one-sweep between 8.3and 2000Hz. The test was performed on the axis and right angledirections of the main valve and armature, for both energized andde-energized states. (Value in the initial stage)Solenoid SpecificationsElectrical entryRated coil voltageDC50/60 Hz ACAllowable voltage fluctuationPower consumption W DCApparent power VA AC100V110V[115V]200V220V[230V]Surge voltage suppressorIndicator light∗The DIN terminal (D) is not available with 10-SY3000.∗110VAC and 115VAC are common, as are 220VAC and 230VAC.∗Energy saving type [0.22W] type is also available.Grommet (G)/(H), L plug connector (L),M plug connector (M), ∗DIN connector (D)24, 12, 6, 5, 3∗100, 110, 200, 220±10% of rated voltage0.5 {Lamp absorber: 0.55(DIN connector with lamp: 0.6)}0.9 (Lamp absorber: 1.0)1.0 (Lamp absorber: 1.1)[1.1 (Lamp absorber: 1.2)]1.8 (Lamp absorber: 1.9)1.9 (Lamp absorber: 2.0)[2.2 (Lamp absorber: 2.3)]Diode (ZNR for DIN terminal, zener diode for G, L or M non-polan type)LED (Neon bulb for AC type DIN terminal)DirectionalControl ValveResponse TimeNote) According to JISB8375-1981 dynamic performance test(With coil temperature of 20°C, at rated voltage and without surge voltage suppressor)10-SY3000Actuation2 position single2 position double3 positionResponse time ms(0.5 MPa)Withoutlight/surgeWith light/surge suppressersuppresser S, Z type R, U type12 or less 15 or less 12 or less10 or less 13 or less 10 or less15 or less 20 or less 16 or less10-SY7000Actuation2 position single2 position double3 positionResponse time ms(0.5 MPa)Without With light/surge suppresserlight/surgesuppresser S, Z type R, U type31 or less 38 or less 33 or less27 or less 30 or less 28 or less50 or less 56 or less 50 or less10-SY5000Actuation2 position single2 position double3 positionResponse time ms(0.5 MPa)Without With light/surge suppresserlight/surgesuppresser S, Z type R, U type19 or less 26 or less 19 or less18 or less 22 or less 18 or less32 or less 38 or less 32 or less271