Pneumatic Clean Series

Series 10-AWMMist Separator Regulator703How to OrderAccessory part no.AccessoryApplicable modelBracket assembly Note 10)10-AWM20Pressure gauge Note 11)15Clean series∗ "J" must always be selected.10 AWM 30 F 03 BG JNMist separator regulatorBody size20 30 40Thread typeNil RcNNote 1) NPTFNote 2) GNote 1) Drain guide is NPT1/8 (applicable to10-AWM20), and NPT1/4(applicable to 10-AWM30, 40).Note 2) Drain guide is G1/8 (applicable to10-AWM20), and G1/4 (applicable to10-AWM30, 40).AccessoryOptional specificationsStandard specificationsModelPort sizesFluidProof pressureMaximum operating pressureSet pressure rangePressure gauge port sizeAmbient and fluid temperatureFiltration accuracyOutlet side oil mist concentrationRated flow {l/min (ANR)} Note 8)Drain capacity (cm 3 )Drain guide piping portConstruction1.0 MPa0.2 MPaSymbol01020304Portsize1/81/43/81/220——AW20P-270ASG49-10-01G49-2-01Port sizeBody sizeNote 8) When the inlet pressure is 0.5MPa. The flow rate varies depending on the inlet pressure.Note 9) When the compressor oil mist discharge concentration is 30mg/m 3 (ANR).30——With bracketRound pressure gaugeWith set nut0.02 to 0.2 MPa settingMetal bowlNylon bowlMetal bowl with level gaugeWith bowl guardDrain guideNon-relieving typeFlow direction: Right to leftName plate, caution plate for bowl, andpressure gauge in imperial units (PSI, °F)40—AccessoriesNote 3)Symbol DescriptionApplicablemodelNilBNote 4)—With bracketWith round—GHpressure gauge(without limitindicator)With set nut(for panel mount)10-AWM20 to 4010-AWM20 to 4010-AWM20 to 40Note 3) Optional parts are notassembled and are suppliedloose at the time of shipment.Note 4) Pressure gauge mountingscrew is 1/8: 10-AWM20 to30, and 1/4: 10-AWM40.Pressure gauge is G49 type.10-AWM2010-AWM3010-AWM401/8, 1/4 1/4, 3/8 1/4, 3/8, 1/21/8Air1.5 MPa1.0 MPa0.05 to 0.85 MPa1/81/415081/8–0.5 to 60°C (with no freezing)0.3 µm (95% filtered particle size)Maximum 1.0 mg/m 3 (ANR) Note 9) (approx. 0.8 ppm)330 251/4 Relieving type820451/410-AWM30AR30P-270ASG49-10-01G49-2-01Note 10) Assembly includes a bracket and set nuts.Note 11) in part numbers for a pressure gauge indicates a type of connection thread. The symbol for thread type is Nil: R, N: NPT.Optional specificationsSymbol DescriptionApplicablemodel1 Note 5) 0.02 to 0.2 MPa setting 10-AWM20 to 4026Metal bowlNylon bowl10-AWM20 to 4010-AWM20 to 408 Metal bowl with level gauge 10-AWM30, 40C With bowl guard 10-AWM20NoteJDrain guide 1/8 10-AWM20Drain guide 1/4 10-AWM30, 406)NRNote 7)Non-relievingFlow direction: Right to leftName plate, caution plate for10-AWM20 to 4010-AWM20 to 40Z bowl, and pressure gaugein imperial units (PSI, °F)10-AWM20 to 40When more than one specification is required, indicate in alphanumeric order.Note 5) The only difference from the standard specifications is the adjusting spring for the regulator. It does notrestrict the setting of 0.2 MPa or more.Note 6) Without a valve function.Note 7) For NPT thread type.This product is for overseas use only according to the new Measurement Law. (The SI unit type is provided for use in Japan.): Combination available : Combination not availableAccessory/Optional specification combinations : Varies depending on the model : Available only with NPT threadCombination Accessory Optional specificationApplicable mist separator regulatorAccessory/Optional specificationsB G H 1 2 6 8 C J N R Z 10-AWM20 10-AWM30, 40SymbolBGH–1–2–6–8–C–J–N–R–Z10-AWM40AR40P-270ASG49-10-02G49-2-02