Pneumatic Clean Series

Series 10-AWDMicro-Mist Separator Regulator705How to Order17Clean series∗ "J" must always be selected.10 AWD 30 F 03 BG JNMicro-mist separator regulatorBody size20 30 40Thread typeNil RcN Note 1) NPTFNote 2) GNote 1) Drain guide is NPT1/8 (applicable to10-AWD20), and NPT1/4 (applicableto 10-AWD30, 40).Note 2) Drain guide is G1/8 (applicable to10-AWD20), and G1/4 (applicable to10-AWD30, 40).Standard specificationsModelPort sizesFluidProof pressureMaximum operating pressureSet pressure rangePressure gauge port sizeAmbient and fluid temperatureFiltration accuracyOutlet side oil mist concentrationRated flow {l/min (ANR)} Note 8)Drain capacity (cm 3 )Drain guide piping portConstructionAccessory part no.AccessoryApplicable modelBracket assembly Note 10)10-AWD20Pressure gauge Note 11)AccessoryOptional specifications1.0 MPa0.2 MPaSymbol01020304Portsize1/81/43/81/2Port sizeBody size20——AW20P-270ASG49-10-01G49-2-0130——With bracketRound pressure gaugeWith set nut0.02 to 0.2 MPa settingMetal bowlNylon bowlMetal bowl with level gaugeWith bowl guardDrain guideNon-relieving typeFlow direction: Right to leftName plate, caution plate for bowl, andpressure gauge in imperial units (PSI, °F)40—AccessoriesNote 3)Symbol DescriptionApplicablemodelNil —B With bracketNote 4) With roundGHpressure gauge(without limitindicator)—10-AWD20 to 4010-AWD20 to 40With set nut10-AWD20 to 40(for panel mount)Note 3) Optional parts are notassembled and are suppliedloose at the time of shipment.Note 4) Pressure gauge mountingscrew is 1/8: 10-AWD20 to30, and 1/4: 10-AWD40.Pressure gauge is G49 type.Optional specificationsSymbol DescriptionApplicablemodel1 Note 5) 0.02 to 0.2 MPa setting 10-AWD20 to 4026Metal bowlNylon bowl10-AWD20 to 4010-AWD20 to 408 Metal bowl with level gauge 10-AWD30, 40C With bowl guard 10-AWD20NoteJDrain guide 1/8 10-AWD20Drain guide 1/4 10-AWD30, 406)NRNote 7)Non-relievingFlow direction: Right to leftName plate, caution plate for10-AWD20 to 4010-AWD20 to 40Z bowl, and pressure gaugein imperial units (PSI, °F)10-AWD20 to 40When more than one specification is required, indicate in alphanumeric order.Note 5) The only difference from the standard specifications is the adjusting spring for the regulator. It does notrestrict the setting of 0.2 MPa or more.Note 6) Without a valve function.Note 7) For NPT thread type.This product is for overseas use only according to the new Measurement Law. (The SI unit type is provided for use in Japan.): Combination available : Combination not availableAccessory/Optional specification combinations : Varies depending on the model : Available only with NPT threadApplicable micro-mistCombination Accessory Optional specificationseparator regulatorAccessory/Optional specificationsB G H 1 2 6 8 C J N R Z 10-AWD20 10-AWD30, 4010-AWD2010-AWD3010-AWD401/8, 1/4 1/4, 3/8 1/4, 3/8, 1/21/8Air1.5 MPa1.0 MPa0.05 to 0.85 MPa1/81/4–0.5 to 60°C (with no freezing)0.01 µm (95% filtered particle size)Maximum 0.1 mg/m 3 (ANR) Note 9) (before saturated with oil: 0.01 mg/m 3 (ANR) or less, approx. 0.008 ppm)9081/8Note 8) When the inlet pressure is 0.5 MPa. The flow rate varies depending on the inlet pressure.Note 9) When the compressor oil mist discharge concentration is 30 mg/m 3 (ANR).180251/4Relieving type10-AWD30AR30P-270ASG49-10-01G49-2-01Note 10) Assembly includes a bracket and set nuts.Note 11) in part numbers for a pressure gauge indicates a type of connection thread. The symbol for thread type is Nil: R, N: NPT.SymbolBGH–1–2–6–8–C–J–N–R–Z450451/410-AWD40AR40P-270ASG49-10-02G49-2-02