Pneumatic Clean Series

Solenoid Valve 10-SY3000/5000/7000313• External wiring is bundled forone-touch wiring• Clean appearanceWith the flat ribbon cable type, each valve iswired to the printed circuit board of the manifoldbase to allow the external wiring to be bundledwith a 26 pin MIL connector for one-touch wiring.Manifold SpecificationsModelApplicable valveManifold typeP(SUP)/R(EXH) systemStationsA/B portpipingspecificationsPortsizeLocationDirectionP, EA, EB portA, B portManifold base weightW (g) n: StationsFlat ribbon cableInternal wiringRated voltage10-SS5Y3-41P 10-SS5Y3-42P 10-SS5Y5-41P 10-SS5Y5-42P 10-SS5Y7-42P10-SY340 10-SY540 10-SY740Single base type/B mountCommon SUP/EXH4 to 12 stations (Note1) 3 to 12 stations (Note1)Rc1/8M5 X 0.8C4 (ø4 One-touch fitting)C6 (ø6 One-touch fitting)BaseSideManifold Internal Wiring (Non-polar type)Rc1/4Rc1/4Rc1/8 Rc1/8 Rc1/4 Rc1/4C4 (ø4 One-touch fitting)C6 (ø6 One-touch fitting)C6 (ø6 One-touch fitting)C8 (ø8 One-touch fitting)C6 (ø6 One-touch fitting)C8 (ø8 One-touch fitting)C10(ø10 One-touch fitting)W=39n+83 W=48n+99 W=67n+118 W=88n+151 W=109n+174Flat ribbon cable connector Socket: 26 pin MIL type with strain relief (MIL-C-83503 compliant)Common to +COM and -COM (Z type is only compatible with +COM).12, 24VDC 100, 110VACNote1) In case of 10 or more stations (5 or more stations with 10-SS5Y7), supply pressure to P portson both sides and exhaust from EA and EB ports on both sides.Note2) The withstand voltage specification for the wiring unit is equivalent to class 1 in JIS C0704.Flow CharacteristicsModel 1,5,3(P,EA,EB)SS5Y3-41P Rc1/8SS5Y3-42P Rc1/8SS5Y5-41P Rc1/4SS5Y5-42P Rc1/4SS5Y7-42P Rc1/4Port sizeFlow characteristics4,214/2 (PA/B)4/25/3 (A/BEA/EB)(A,B) C[dm 3 /(s·bar)] b Cv C[dm 3 /(s·bar)] b CvC6C6C8C8C100.750.751.81.93.00.190.200.230.200.250.180.180.440.460.750.810.821.91.93.0Note) Value is for manifold with 5 stations and individually operated 2 position type.0.230.200.160.120.120.200.200.450.430.66Note)No terminal number is indicated on the connector. The terminalnumbers in the connector wiring diagram show the correlation thatassumes the terminals on the flat ribbon cable connector werenumberd 1 to 26 starting from the side marked with a triangle, asshown in the figure to the right.•In case of 10 or more stations, wire both COM pins.•For single solenoid, connect to the solenoid A side.•The maximum number of stations is 12. Contact SMC if more stations are required.CautionNon-polar type (U) valves with DC electrical connection can be used for both negative and positiveCOM. However, always use the positive COM with the Z type, since valves will not be actuated whenthe negative COM is used.294