OMRON Sysdrive 3G3HV - Detector Cooling Section

More documents

Recommendations

Info

Control Circuit Terminals for All 3G3HV Models Symbol Name Function Signal level Input S1 Forward run/Stop Stops at OFF. Photocoupler S2 Multi-function input 1 (S2) Set by constant n035 (reverse run/stop). 24 VDC, 8 mA Output S3 Multi-function input 2 (S3) Set by constant n036 (external error a). S4 Multi-function input 3 (S4) Set by constant n037 (error reset). S5 Multi-function input 4 (S5) Set by constant n038 (multi-step speed reference 1). S6 Multi-function input 5 (S6) Set by constant n039 (multi-step speed reference 2). SC Sequence input common Common for S1 to S6. FS Frequency reference power supply DC power supply for frequency reference. 15 VDC, 20 mA FV Frequency reference input (voltage) Voltage input terminal for frequency reference. FI Frequency reference input (current) Current input terminal for frequency reference. 0 to 10 VDC (20 kΩ) 4 to 20 mA (250 kΩ) FC Frequency reference input common Common for FV, F1. --- E (G) Shielded wire connection ground Shielded terminal for sequence and frequency reference inputs. (see note 2) --- MA Multi-function contact output 1 (normally Set by constant n040 (error) Contact outmally open) put MB Multi-function contact output 1 (nor- 30 VDC, 1 A closed) max. 250 VAC, 1 A MC Multi-function contact output 1 common Common for MA, MB max. M1 Multi-function contact output 2 (normally Set by constant n041 (running) open) M2 Multi-function contact output 2 common Common for M1 AM Multi-function analog output Set by constant n048 (output frequency) 0 to 10 VDC, AC Multi-function analog output common Common for AM 2 mA Note Note 1. The settings shown in parentheses in the “Function” column for the multi-function inputs and multi-function contact outputs indicate default settings. 2. Do not connect a grounding wire to the E (G) terminal. Connect the grounding wire to the ground terminal of the main circuit terminals.
Standard Connection Diagram For Inverter Models of 200- to 400-V Class with 3.7- to 15-kW Output DC reactor (External connection possible) Braking Resistor Unit (see note) (optional) Three-phase, 200 (400) VAC Forward rotation/Stop Multi-function input 1 Multi-function input 2 Multi-function input 3 Multi-function input 4 Multi-function input 5 Common L1 (R) L2 (S) L3 (T) T1 (U) T2 (V) T3 (W) Three-phase induction motor Multi-function contact output 1 (Normally open contact) (Normally closed contact) Common Multi-function contact output 2 Common Shielded wire Variable resistor for frequency reference (voltage input) Multi-function analog output Common Voltmeter Frequency reference (current input) Note: These terminals of the 3G3HV-A2110 and 3G3HV-A2150 connect to the Braking Unit and Braking Resistor Unit.
Page 1 and 2: Function The 3G3HV High-capacity Ge
Page 3 and 4: • Two acceleration times and two
Page 5 and 6: Digital Operator Easy-setting indic
Page 7 and 8: 3G3HV-A2110/-A2150/-A4110/-A4150 E
Page 9 and 10: 3G3HV-B2750/-B411K/-B416K External
Page 11 and 12: Installation Conditions Cautions a
Page 13 and 14: Wiring Cautions and Warnings ! WAR
Page 15 and 16: • Do not mount the front cover wi
Page 17: 400-V Class Model 3G3HV- A4037 to A
Page 21 and 22: Wiring Around the Main Circuit Syst
Page 23 and 24: Voltage class Model Terminal Termin
Page 25 and 26: Round Solderless Terminals and Tigh
Page 27 and 28: peak current may flow through the i
Page 29 and 30: inrush current will actuate the ove
Page 31 and 32: • When using more than one Invert
Page 33 and 34: atio of harmonics in the output cur
Page 35 and 36: Do not ground the secondary winding
Page 37 and 38: 200-V Class with 3.7- to 7.5-kW Out
Page 39 and 40: Preparation Procedure Installation
Page 41 and 42: Nomenclature Easy-setting indicator
Page 43 and 44: Indicator Item Function Fref Speed
Page 45 and 46: Monitor Monitor item No. U-01 Frequ
Page 47 and 48: Check the rated input voltage of th
Page 49 and 50: Change the frequency reference and
Page 51 and 52: Set Values Set value Run command Fr
Page 53 and 54: n027 Frequency Reference 3 Setting
Page 55 and 56: n039 Multi-function Input 5 (S6) Se
Page 57 and 58: Select one of the 15 V/f patterns p
Page 59 and 60: n012 Maximum Frequency (FMAX) Setti
Page 61 and 62: Energy-saving Mode The Inverter in
Page 63 and 64: Note speed motors (e.g., spindle mo
Page 65 and 66: does not save unnecessary power sup
Page 67 and 68: PID Control PID (proportional, inte
Page 69 and 70:
PID Control Function Refer to the f
Page 71 and 72:
Set Values • The parameters n086,
Page 73 and 74:
PID Parameters The following can be
Page 75 and 76:
Suppression of Short-cycle Vibratio
Page 77 and 78:
Function No. Name Description Setti
Page 79 and 80:
Page 81 and 82:
Group 2: n035 to n049 Function No.
Page 83 and 84:
Function Analog monitor function se
Page 85 and 86:
Page 87 and 88:
Function I/O phase loss detection N
Page 89 and 90:
Page 91 and 92:
Note 1. Do not set n001 to any valu
Page 93 and 94:
Set Values Set value 0 The motor ca
Page 95 and 96:
Characteristics of V/f Patterns Ge
Page 97 and 98:
Note The V/f pattern will be a stra
Page 99 and 100:
n029 Setting range Inching Frequenc
Page 101 and 102:
Set Values Set Description value 0
Page 103 and 104:
2-wire Sequence (n035 = 0) Wiring E
Page 105 and 106:
Acceleration/Deceleration Time Swit
Page 107 and 108:
Inverter Overheat Warning (Set Valu
Page 109 and 110:
• The functions of multi-function
Page 111 and 112:
Optional Frequency Detection: Outpu
Page 113 and 114:
Note 2. To permit the Inverter to o
Page 115 and 116:
n Carrier 0frequency (fc) 5 2.5 kHz
Page 117 and 118:
When the Inverter is in normal oper
Page 119 and 120:
n066 • Set with n065 DC control t
Page 121 and 122:
• Set with n071 and n072 current
Page 123 and 124:
Set Values Set Description value 0
Page 125 and 126:
Protective and Diagnostic Functions
Page 127 and 128:
Data display rh rr Description Brak
Page 129 and 130:
Data display %h3 flashing %l3 flash
Page 131 and 132:
verter if n002 is set to 0 or 2 or
Page 133 and 134:
Controller Receives Noise When Inve
Page 135 and 136:
Maintenance and Inspection Caution
Page 137 and 138:
Specifications of Inverters General
Page 139 and 140:
Control Characteristics Model 3G3HV
Page 141 and 142:
3G3HV-PCMA2 Voltage/Current Convers
Page 143 and 144:
External Dimensions 75 min. 120 min
Page 145 and 146:
3G3IV-PJVOP95 Analog Operator (Mini
Page 147 and 148:
3G3IV-PLKEB Braking Resistor Unit T
Page 149 and 150:
3G3IV-PUZBAB A MH AC Reactor Connec
Page 151 and 152:
Dimensions A B B1 C D E F H J K L M
Page 153 and 154:
External Dimensions Model 3G3IV- Ap
Page 155 and 156:
3G3IV-PLF Output Noise Filter (Toki
Page 157 and 158:
Notes on Using the Inverter for a M
Page 159 and 160:
Motor Burnout Due to Insufficient D
Page 161 and 162:
Voltage Enclosure rating Max. motor
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Group 2: n035 to n049 Function No.
Page 169 and 170:
Function Analog monitor function se
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Function No. n095 n096 n097 n098 n0
show all

OMRON Sysdrive 3G3HV - Detector Cooling Section

Create successful ePaper yourself

Delete template?

Save as template?