OMRON Sysdrive 3G3HV - Detector Cooling Section

More documents

Recommendations

Info

Note With 400-V Inverters, the setting range upper limits and default settings are double those shown in the table.
Function No. Name Description Setting range Accelera- n019 Acceleration The time required for the output frequency 0.0 to tion/Decel- time 1 to be 100% from 0% of the maximum fre- 3,600 eration time quency. selection n020 Deceleration time 1 S-shaped characteristic time selection Frequency reference selection n021 n022 n023 n024 The time required for the output frequency to be 0% from 100% of the maximum frequency. Valid if acceleration/deceleration time switching command is selected for multifunction input. Valid if acceleration/deceleration time switching command is selected for multifunction input. 0: No s-shaped characteristic time 1: 0.2 s 2: 0.5 s 3: 1.0 s 0: 0.1-Hz units 1: 0.1% units 2to 39: r/min (r/min = 120 x frequency/n024 Set n024 to the number of poles of the motor.) 40 to 3,999: Determine the display method of the maximum frequency set with n012. Example: Set n024 to 1100 so that “10.0” will be displayed at the maximum frequency. Set frequency reference using the unit set with n024. Frequency reference with multi-step speed command 1 turned ON. Frequency reference with multi-step speed command 2 turned ON. Frequency reference with multi-step speed command 1 and 2 turned ON. Frequency reference with inching command turned ON. Acceleration time 2 Deceleration time 2 S-shaped characteristic time selection Unit of frequency reference Frequency reference n025 Frequency reference 1 selection n026 Frequency reference 2 n027 Frequency reference 3 n028 Frequency reference 4 n029 Inching frequency reference Output frequency n030 Output fre- limit quency up- selection per limit n031 Output frequency lower limit Set output frequency upper limit with 1% units based on max. frequency set with n012 as 100%. Set output frequency lower limit with 1% units based on max. frequency set with n012 as 100%. 0.0 to 3,600 0.0 to 3,600 0.0 to 3,600 0 to 3 1 0 to 3,999 0 to maximum frequency 0 to 100 0 to 100 Default setting 10.0 10.0 10.0 10.0 0 6.0 0.0 0.0 0.0 6.0 100 0
Page 1 and 2:
Function The 3G3HV High-capacity Ge
Page 3 and 4:
• Two acceleration times and two
Page 5 and 6:
Digital Operator Easy-setting indic
Page 7 and 8:
3G3HV-A2110/-A2150/-A4110/-A4150 E
Page 9 and 10:
3G3HV-B2750/-B411K/-B416K External
Page 11 and 12:
Installation Conditions Cautions a
Page 13 and 14:
Wiring Cautions and Warnings ! WAR
Page 15 and 16:
• Do not mount the front cover wi
Page 17 and 18:
400-V Class Model 3G3HV- A4037 to A
Page 19 and 20:
Standard Connection Diagram For In
Page 21 and 22:
Wiring Around the Main Circuit Syst
Page 23 and 24:
Voltage class Model Terminal Termin
Page 25 and 26:
Round Solderless Terminals and Tigh
Page 27 and 28: peak current may flow through the i
Page 29 and 30: inrush current will actuate the ove
Page 31 and 32: • When using more than one Invert
Page 33 and 34: atio of harmonics in the output cur
Page 35 and 36: Do not ground the secondary winding
Page 37 and 38: 200-V Class with 3.7- to 7.5-kW Out
Page 39 and 40: Preparation Procedure Installation
Page 41 and 42: Nomenclature Easy-setting indicator
Page 43 and 44: Indicator Item Function Fref Speed
Page 45 and 46: Monitor Monitor item No. U-01 Frequ
Page 47 and 48: Check the rated input voltage of th
Page 49 and 50: Change the frequency reference and
Page 51 and 52: Set Values Set value Run command Fr
Page 53 and 54: n027 Frequency Reference 3 Setting
Page 55 and 56: n039 Multi-function Input 5 (S6) Se
Page 57 and 58: Select one of the 15 V/f patterns p
Page 59 and 60: n012 Maximum Frequency (FMAX) Setti
Page 61 and 62: Energy-saving Mode The Inverter in
Page 63 and 64: Note speed motors (e.g., spindle mo
Page 65 and 66: does not save unnecessary power sup
Page 67 and 68: PID Control PID (proportional, inte
Page 69 and 70: PID Control Function Refer to the f
Page 71 and 72: Set Values • The parameters n086,
Page 73 and 74: PID Parameters The following can be
Page 75 and 76: Suppression of Short-cycle Vibratio
Page 77: Function No. Name Description Setti
Page 81 and 82: Group 2: n035 to n049 Function No.
Page 83 and 84: Function Analog monitor function se
Page 85 and 86: Function No. Name Description Setti
Page 87 and 88: Function I/O phase loss detection N
Page 89 and 90: Function No. Name Description Setti
Page 91 and 92: Note 1. Do not set n001 to any valu
Page 93 and 94: Set Values Set value 0 The motor ca
Page 95 and 96: Characteristics of V/f Patterns Ge
Page 97 and 98: Note The V/f pattern will be a stra
Page 99 and 100: n029 Setting range Inching Frequenc
Page 101 and 102: Set Values Set Description value 0
Page 103 and 104: 2-wire Sequence (n035 = 0) Wiring E
Page 105 and 106: Acceleration/Deceleration Time Swit
Page 107 and 108: Inverter Overheat Warning (Set Valu
Page 109 and 110: • The functions of multi-function
Page 111 and 112: Optional Frequency Detection: Outpu
Page 113 and 114: Note 2. To permit the Inverter to o
Page 115 and 116: n Carrier 0frequency (fc) 5 2.5 kHz
Page 117 and 118: When the Inverter is in normal oper
Page 119 and 120: n066 • Set with n065 DC control t
Page 121 and 122: • Set with n071 and n072 current
Page 123 and 124: Set Values Set Description value 0
Page 125 and 126: Protective and Diagnostic Functions
Page 127 and 128: Data display rh rr Description Brak
Page 129 and 130:
Data display %h3 flashing %l3 flash
Page 131 and 132:
verter if n002 is set to 0 or 2 or
Page 133 and 134:
Controller Receives Noise When Inve
Page 135 and 136:
Maintenance and Inspection Caution
Page 137 and 138:
Specifications of Inverters General
Page 139 and 140:
Control Characteristics Model 3G3HV
Page 141 and 142:
3G3HV-PCMA2 Voltage/Current Convers
Page 143 and 144:
External Dimensions 75 min. 120 min
Page 145 and 146:
3G3IV-PJVOP95 Analog Operator (Mini
Page 147 and 148:
3G3IV-PLKEB Braking Resistor Unit T
Page 149 and 150:
3G3IV-PUZBAB A MH AC Reactor Connec
Page 151 and 152:
Dimensions A B B1 C D E F H J K L M
Page 153 and 154:
External Dimensions Model 3G3IV- Ap
Page 155 and 156:
3G3IV-PLF Output Noise Filter (Toki
Page 157 and 158:
Notes on Using the Inverter for a M
Page 159 and 160:
Motor Burnout Due to Insufficient D
Page 161 and 162:
Voltage Enclosure rating Max. motor
Page 163 and 164:
Function No. Name Description Setti
Page 165 and 166:
Page 167 and 168:
Group 2: n035 to n049 Function No.
Page 169 and 170:
Function Analog monitor function se
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Function No. n095 n096 n097 n098 n0
show all

OMRON Sysdrive 3G3HV - Detector Cooling Section

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?