II - DCE FEL ČVUT v Praze

Index
Hardware interrupt lost
SM 321; DI 4 x NAMUR, 2-11
SM 331; AI 2 x 0/4...20mA HART, 3-47
SM 331; AI 4 x 0/4...20 mA, 3-47
SM 331; AI 8 x TC/4 x RTD, 3-47
Hardware interrupt on exceeding limit, enable,
3-42, 3-43, 4-11
Hardware interrupts trailing edge, enable, 2-8
HART, 4-3
advantages, 4-3
application, 4-3, 4-6
channel, 4-15, 4-26
introduction, 4-3
measurement mode, 4-11
mode of operation, 4-4
parameter assignment tool, 4-6
primary variable, 4-37
system, 4-6
technical specification, 4-32
HART analog input, 4-1
2-wire transducers, 3-35
4-wire transducers, 3-35
data record format, 4-26
Default settings, 4-16
parameters missing, 4-28
wire break monitoring, 4-16
HART analog input , technical data, 4-15
HART analog module
operation, 4-9
setup, 4-8
using the modules, 4-2
HART analog modules, product overview, 4-2
HART analog output, 4-1
data record format, 4-27
HART channel error, diagnostic of HART analog
input, 4-29
HART command, 4-4, 4-30
data record format, 4-31
example, 4-5
inseparable command sequence, 4-31
HART communication, 4-25
data record format, 4-30
state, 4-34
HART field device, recognition, 4-35
HART field devices, 4-4
HART group error, SM 331; AI 2 x 0/4...20mA
HART, 4-13
HART hand-held, 4-6
HART identification, field device, 4-35
HART interface, 4-1
HART master, 4-2
Index-4
HART parameter, 4-4
example, 4-5
HART protocol, 4-3, 4-4
HART respons, 4-4
HART response, 4-30
data ready, 4-31
data record format, 4-32
processing state, 4-31, 4-32
HART response data, evaluating, 4-32
HART signal, 4-4
influence, 4-16
HART signals
influencing by, 3-66
interference due to, 4-16
HART slaves, 4-2
HART status byte, 4-33
HART status bytes, 4-5, 4-10
HART status display, LED green, 4-11
Hazardous, location, 2-3, 2-15, 2-24, 3-55, 3-64,
3-69, 4-7, 4-17, 4-22
HCF, 4-3
I
I/O bus, Glossary-7
IM 153, slave interface, 4-7
IM 153-2, slave interface, 2-3, 2-15, 2-24, 3-55,
3-64, 3-69
Incorrect parameter in module, SM 321; DI 4 x
NAMUR, 2-11
Incorrect parameters in module
SM 322; DO 4 x 15V/20mA, 2-22
SM 322; DO 4 x 24V/10mA, 2-22
SM 331; AI 2 x 0/4...20mA HART, 3-47
SM 331; AI 4 x 0/4...20 mA, 3-47
SM 331; AI 8 x TC/4 x RTD, 3-47
SM 332; AO 4 x 0/4...20 mA, 3-49
Influencing, by HART signals, 3-66
Input delay, 2-8
Inserting and removing
Ex I/O modules, 1-5
HART analog input, 4-16
Installation
intrinsically-safe, 2-3, 2-15, 2-24, 3-55,
3-64, 3-69, 4-7, 4-17
sample configuration, 4-7
Integration time, 4-11
Integration times, HART analog input, 4-16
Interference, due to HART signals, 4-16
I/O Modules with Intrinsically-Safe Signals
C79000-G7076-C152-04