AGREEMENT between BROWARD COUNTY and Cummings ...

More documents

Recommendations

Info

DIVISION 1 SPECIFICATIONS SECTION 01340 – SHOP DRAWINGS, PRODUCT DATA AND SAMPLES F. Submittals that are received from sources other than through CONTRACTOR’s office will be returned without action. Delays resulting there from shall be CONTRACTOR’s responsibility. G. Package each submittal appropriately for transmittal and handling. H. Distribute reproductions of shop drawings, copies of product data, and samples, which bear CONSULTANT’s stamp of approval, to jobsite file, record documents file, subcontractors, suppliers and other entities requiring information. I. Do not fabricate products or begin work, which required submittals until return of submittal with CONSULTANT’s and CPM’s acceptance. 1.07 CPM’S AND CONSULTANT’S ACTION: A. Where action and return is required or requested, CONSULTANT will review each submittal, mark with action, and where possible return with reasonable promptness. CPM will forward all comments to the CONSULTANT 1. Where submittal must be held for coordination, CONTRACTOR will be so advised by the CONSULTANT. 2. Affix stamp and initial or sign, and indicate requirements for resubmittal, or acceptance of submittal. 3. Return submittals to CONTRACTOR for distribution or for resubmission. 4. CONSULTANT will review submittals for design content only. CPM will review submittals for construction and installation considerations. B. Final Unrestricted Release: When submittal is returned marked “No Exceptions Taken”, work may proceed, provided it complies with Contract Documents. C. Final-But-Restricted-Release: When submittal is returned marked “Note Markings”, Work may proceed, provided it complies with notations and corrections on submittal and with Contract Documents. D. Returned for Resubmittal: Exhibit 2 Page 282 of 379 1. When submittal is returned marked “Revise and Resubmit” or is unmarked, do not proceed with Work. 2. Revise submittal in accordance with notations and resubmit without delay to obtain difference action marking. E. Other Action: Where submittal is returned for other reasons, with the CPM or CONSULTANT’s explanation included, it will be marked “Not Accepted”. PART 2 - PRODUCTS PART 3 - EXECUTION (Not Used) (Not Used) ATTACHMENTS: Submittal Transmittal Section 01340 Shop Drawings, Product Data and Samples Page 77
DIVISION 1 SPECIFICATIONS SECTION 01340 – SHOP DRAWINGS, PRODUCT DATA AND SAMPLES Exhibit 2 Page 283 of 379 SUBMITTAL TRANSMITTAL Project Name _______________________________________ Submittal No. __________________ CM-at-Risk Contractor (CMR)__________________________________________________________________________ Subcontractor/Supplier________________________________________________________________________ Specification Section __________________Paragraph Reference _____________________________________ Drawing Number _____________________Section/Detail Reference ___________________________________ Manufacturer ________________________ Model No. ______________________________________________ Transmittal Record CMR to PM Attention: Date Sent Date Received Date Due Quantity Reviewed by: CMR to Consultant Consultant to Subconsultant Subconsultant to Consultant Consultant to PM PM to CMR DEVIATIONS: None __________; As Listed _____________ SPACE REQUIREMENTS: As Designed ___________; Different and as Listed _____________ THIS SUBMITTAL CONSISTS OF (SELECT): Product Data Maintenance Instructions Shop Drawings Manufacturer’s Test Report Installation Instructions Manufacturer’s Approval of Applicator/Installer Material Schedule Others (include list) Quantity: __________ Description: _____________________________________________ Sepia ________________________________________________________________________ Prints ____________________________________________________________________________ Samples ____________________________________________________________________________ Check one of the following: Submitted Resubmitted By___________________________________________________ Date____________________________________________ Signature SUBMITTAL TRANSMITTAL REVIEW Consultant’s project # _____________ Consultant’s tracking # _______________ NO EXCEPTIONS TAKEN NOTE COMMENTS REJECTED RESUBMIT CONSULTANT’S COMMENTS: _____________________________________________________________________________________________ ____ Section 01340 Shop Drawings, Product Data and Samples Page 78
Page 1 and 2:
Exhibit 2 Page 1 of 379 AGREEMENT b
Page 3 and 4:
Exhibit 2 Page 3 of 379 Terminal 4
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Terminal 4 Gate Replacement - Weste
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Exhibit 2 Page 99 of 379 Owner Cont
Page 101 and 102:
Exhibit 2 Page 101 of 379 TABLE OF
Page 103 and 104:
Exhibit 2 Page 103 of 379 OVERVIEW
Page 105 and 106:
Exhibit 2 Page 105 of 379 OVERVIEW
Page 107 and 108:
Exhibit 2 Page 107 of 379 OCIP PROG
Page 109 and 110:
Exhibit 2 Page 109 of 379 OCIP INSU
Page 111 and 112:
Exhibit 2 Page 111 of 379 OCIP INSU
Page 113 and 114:
Exhibit 2 Page 113 of 379 CONTRACTO
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Exhibit 2 Page 123 of 379 CLAIM REP
Page 125 and 126:
Exhibit 2 Page 125 of 379 CLAIM REP
Page 127 and 128:
AONWRAP WEB INSTRUCTION Exhibit 2 P
Page 129 and 130:
AONWRAP WEB INSTRUCTION 10. Type yo
Page 131 and 132:
AONWRAP WEB INSTRUCTION Exhibit 2 P
Page 133 and 134:
Exhibit 2 Page 133 of 379 Form-3 En
Page 135 and 136:
Exhibit 2 Page 135 of 379 Enrollmen
Page 137 and 138:
Form-4 On-Site(s) Payroll Report In
Page 139 and 140:
Form-5 Notice of Work Completion In
Page 141 and 142:
Exhibit 1 - Sample Certificate of I
Page 143 and 144:
Exhibit 3 - First Report of Injury
Page 145 and 146:
Exhibit 2 Page 145 of 379
Page 147 and 148:
TABLE OF CONTENT Exhibit 2 Page 147
Page 149 and 150:
Exhibit 2 Page 149 of 379 SECURITY
Page 151 and 152:
INTRODUCTION Exhibit 2 Page 151 of
Page 153 and 154:
DEFINITIONS Exhibit 2 Page 153 of 3
Page 155 and 156:
ACRONYMS Exhibit 2 Page 155 of 379
Page 157 and 158:
Conduct hazard communication traini
Page 159 and 160:
12. Review and evaluate contractors
Page 161 and 162:
or minimize exposures that will or
Page 163 and 164:
2) Positioning device system allows
Page 165 and 166:
F. Welding and Cutting Exhibit 2 Pa
Page 167 and 168:
13) Complete and file on site a Loc
Page 169 and 170:
M. Job Safety Analysis Exhibit 2 Pa
Page 171 and 172:
SAFETY TRAINING Exhibit 2 Page 171
Page 173 and 174:
4. Contractor Safety Audit This Saf
Page 175 and 176:
d) The OCIP insurance carrier perso
Page 177 and 178:
Exhibit 2 Page 177 of 379 EMERGENCY
Page 179 and 180:
Obtain a hurricane tracking and inf
Page 181 and 182:
SECURITY Exhibit 2 Page 181 of 379
Page 183 and 184:
D. Security - General Project Rules
Page 185 and 186:
I. Delivery and Removal of Material
Page 187 and 188:
Exhibit 2 Page 187 of 379 FIRST REP
Page 189 and 190:
Page 191 and 192:
Exhibit 2 Page 191 of 379 d. Analyz
Page 193 and 194:
Exhibit 2 Page 193 of 379 4. PPE cu
Page 195 and 196:
Exhibit 2 Page 195 of 379 WITNESS S
Page 197 and 198:
Exhibit 2 Page 197 of 379 Sequence
Page 199 and 200:
Exhibit 2 Page 199 of 379 LOCK-OUT
Page 201 and 202:
Exhibit 2 Page 201 of 379 ORIENTATI
Page 203 and 204:
Exhibit 2 Page 203 of 379 SAFETY OB
Page 205 and 206:
Page 207 and 208:
Exhibit 2 Page 207 of 379 DIVISION
Page 209 and 210:
DIVISION 1 SPECIFICATIONS - SECTION
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
DIVISION 1 SPECIFICATIONS SECTION 0
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232: DIVISION 1 SPECIFICATIONS SECTION 0
Page 281: DIVISION 1 SPECIFICATIONS SECTION 0
Page 285 and 286: DIVISION 1 SPECIFICATIONS - SECTION
Page 303 and 304: Exhibit 2 Page 303 of 379 DIVISION
Page 311 and 312: Exhibit 2 Page 311 of 379 DIVISION
Page 329 and 330: Exhibit 2 Page 329 of 379 PART 1 -
Page 331 and 332: Exhibit 2 Page 331 of 379 Broward C
Page 333 and 334:
Badging Requirements and Ramp Drivi
Page 335 and 336:
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
Page 345 and 346:
Page 347 and 348:
Page 349 and 350:
Exhibit 2 Page 349 of 379 EXHIBIT 1
Page 351 and 352:
Exhibit 2 Page 351 of 379 NUMBER VE
Page 353 and 354:
TERMINAL 4 GATE REPLACEMENT - WESTE
Page 355 and 356:
Page 357 and 358:
Page 359 and 360:
Exhibit 2 Page 359 of 379 TERMINAL
Page 361 and 362:
Exhibit 2 Page 361 of 379 TERMINAL
Page 363 and 364:
Exhibit 2 Page 363 of 379 FORM 1: C
Page 365 and 366:
Exhibit 2 Page 365 of 379 FORM 3 FO
Page 367 and 368:
Exhibit 2 Page 367 of 379 FORM 4: F
Page 369 and 370:
Exhibit 2 Page 369 of 379 FORM OF P
Page 371 and 372:
Exhibit 2 Page 371 of 379 FORM OF P
Page 373 and 374:
MONTHLY (CBE) UTILIZATION REPORT Ex
Page 375 and 376:
FINAL (CBE) UTILIZATION REPORT Exhi
Page 377 and 378:
Exhibit 2 Page 377 of 379 CBE UNAVA
Page 379:
Exhibit 2 Page 379 of 379 CERTIFICA
show all

AGREEMENT between BROWARD COUNTY and Cummings ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?