Attachment 1: Specifications - Metropolitan Washington Airports ...

More documents

Recommendations

Info

DCA TERMINAL A IMPROVEMENTS (NEAR TERM) 10 AUGUST 2012 TASK ORDER 03: LOBBY IMPROVEMENTS – PKG 4 - CURBSIDE CHECK-IN RONALD REAGAN WASHINGTON NATIONAL AIRPORT PROJECT DT1203 a. Type: Tight Buffer b. Core / Cladding Dia. 62.5 / 125 c. Microbend 100 turns @ 50mm: 0.05 max @ 850nm / 1300nm d. Attenuation: 3.5db/km @850nm 1.5db/km @1300nm e. Design Selection: CommScope Systimax P-006-DS-6F-FSUxx (Where XX = Color TBD by MWAA) or approved equal 2. Singlemode Fiber Optic: a. Type: Tight Buffer b. Core / Cladding Dia. 9.6 / 125 c. Microbend 100 turns @ 75mm: 0.05 db max @ 1550nm d. Attenuation: 0.7db/km @1310nm 0.7db/km @15501300nm e. Design Selection: CommScope Systimax P-006-SW-8W-FSUxx (Where XX = Color TBD by MWAA) or approved equal 2.5 DATA COPPER TERMINATIONS A. As specified in Division 27 Section “Communications Equipment Room Fittings.” 2.6 VOICE COPPER TERMINATIONS A. As specified in Division 27 Section “Communications Equipment Room Fittings.” 2.7 COPPER PATCH CORDS A. As specified in Division 27 Section “Communications Equipment Room Fittings.” 2.8 GROUNDING A. As specified in Division 27 Section “Grounding and Bonding for Communications Systems.” PART 3 - EXECUTION 3.1 GENERAL A. As specified in Division 27 Section “Basic Telecommunication Requirements” and Division 27 Section “Premise Wiring Distribution System.” B. Installations shall meet or exceed industry standards and installation practices listed herein. COMMUNICATIONS HORIZONTAL CABLING 27 15 00 - 6
DCA TERMINAL A IMPROVEMENTS (NEAR TERM) 10 AUGUST 2012 TASK ORDER 03: LOBBY IMPROVEMENTS – PKG 4 - CURBSIDE CHECK-IN RONALD REAGAN WASHINGTON NATIONAL AIRPORT PROJECT DT1203 C. Product installations failing to meet standards and practices shall be removed and replaced at no additional cost to The Authority. D. The Contractor shall be responsible for any damage to any surfaces or work disrupted as a result of his work. Repair of surfaces including painting shall be included as necessary. 3.2 INSTALLATION PRACTICES A. General: 1. Install all equipment in strict accordance with the manufacturer’s recommendations and in compliance with the latest issue of the TIA/EIA-568A Telecommunications Standards and BISCI’s Telecommunications Distributions Methods Manual (TDMM) guidelines. 2. The installation shall be in compliance with the requirements of the NEC, OSHA and the rules, regulations and requirements of the FCC. 3. The installation shall comply with federal, city, county and state laws, ordinances, regulations, and codes applicable to the installation. 4. Contractor shall supply all tools and test equipment necessary for successful completion of the Project. 5. If deviations from the Drawings are required, they shall require approval by the COTR prior to placement of the affected work. 6. The locations of raceways, stub ups, outlets, panels, equipment racks and cabinets and other related products as indicated on the Drawings are diagrammatic in location. Contractor should have precise and definite locations accepted by the COTR before proceeding with the installation. 7. Contractor shall field coordinate the exact mounted heights and locations of cable ladder within the Communications rooms prior to installation. B. Cabling Installation Practices: 1. A portion of the PWDS wiring installed within the buildings will be installed above ceilings within existing cable tray in areas used for circulation of environmental air. Cables installed within these areas shall be rated for use in such plenum locations and shall bare the CMP marking. 2. Contractor shall pull cable in accordance with manufacturer’s recommendations, industryaccepted practices and within the limits of cable bend radius and pulling tension specifications. 3. Use pulling lubricants compatible with the cable. Petroleum products shall not be used as cable pulling lubricant. 4. Contractor shall not install more cables in a conduit than shown unless approved in writing by the COTR. 5. Conduit systems shall not exceed 40% cable fill. The Contractor shall provide larger conduit or additional conduit should planned cable fill exceed 40%. 6. Contractor shall plan cable pulls so that the maximum number of cables required in the conduit is pulled simultaneously. 7. Avoid routing horizontal telecommunications cables near sources of EMI. Maintain a minimum clearance of 4 feet from power transformers and motors and 12 inches from fluorescent lighting and power distribution cables. Advise the COTR of any field conditions where EMI issues may arise prior to proceeding with that portion of the work. COMMUNICATIONS HORIZONTAL CABLING 27 15 00 - 7
Page 1:
TECHNICAL SPECIFICATIONS VOLUME I O
Page 4 and 5:
DCA TERMINAL A IMPROVEMENTS (NEAR T
Page 6 and 7:
THIS PAGE INTENTIONALLY LEFT BLANK
Page 8 and 9:
Page 10 and 11:
DCA TERMINAL A IMPROVEMENTS 10 AUGU
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365: THIS PAGE INTENTIONALLY LEFT BLANK
Page 366 and 367: DCA TERMINAL A IMPROVEMENTS (NEAR T
Page 464 and 465:
Page 466 and 467:
Page 468 and 469:
Page 470 and 471:
Page 472 and 473:
Page 474 and 475:
Page 476 and 477:
Page 478 and 479:
Page 480 and 481:
Page 482 and 483:
Page 484 and 485:
Page 486 and 487:
Page 488 and 489:
Page 490 and 491:
Page 492 and 493:
Page 494 and 495:
Page 496 and 497:
Page 498 and 499:
Page 500:
show all

Attachment 1: Specifications - Metropolitan Washington Airports ...

Create successful ePaper yourself

Delete template?

Save as template?