OPERATION MANUAL CompoBus/S

More documents

Recommendations

Info

Precautions for Replacement of Units or Parts Section 6-7 Note Acceptable humidity range with no condensation or frost. 6-7 Precautions for Replacement of Units or Parts 6-7-1 Precautions for Unit Replacement The <strong>CompoBus</strong>/S Master Unit and Slave Units make up the system. The entire system is affected when a Unit is faulty, so a faulty Unit must be repaired or replaced quickly. We recommend having spare Units available to restore operation as quickly as possible. Observe the following precautions when replacing a faulty Unit. After replacement make sure that there are no errors with the new Unit. When a Unit is being returned for repair, attach a sheet of paper detailing the problem and return the Unit to your OMRON dealer. If there is a faulty contact, try wiping the contact with a clean, lint-free cloth dampened with alcohol. Re-mount the Unit after cleaning off any lint. !Caution To prevent electric shock when replacing a Unit, be sure to turn OFF the power supplies to all of the nodes (Master and Slaves) before removing the faulty Unit. 6-7-2 Settings after Unit Replacement 6-7-3 Replacing Relays Unit Acceptable temperature Acceptable humidity* Sensor Terminal 0 to 55°C 35% to 85% Fiber Amplifier Communications Unit –20 to 55°C 35% to 85% Connector Terminal –10 to 55°C 25% to 85% Water-resistant Terminal –10 to 55°C 25% to 85% Analog Terminal –10 to 55°C 25% to 85% CPM1A/CPM2A I/O Link Unit 0 to 55°C 10% to 90% CPM2C I/O Link Unit 0 to 55°C 10% to 90% After replacing a Unit, set the new Unit’s switches to the same settings that were on the old Unit. !Caution When the CPU Unit has been replaced, transfer any required DM Area or HR Area data to the new CPU Unit before restarting operation. Faulty relays or power MOSFET relays in Remote Terminals can be removed and replaced. !Caution Be sure to turn OFF the Slave’s power supply before removing the faulty relay to prevent electric shock. The relay’s pins often bend or break when the relay is removed, so remove faulty relays only. Remote Terminal Relays Use the following procedure to replace a relay in an Remote Terminal. 1,2,3... 1. The relay removal tool attached to the Remote Terminal is used to remove the relay. Align the relay removal tool so that it squeezes the old relay, push it all the way in, and pull it out to remove the relay. 385
Precautions for Replacement of Units or Parts Section 6-7 386 2. Check the orientation of the new relay carefully and insert it to the same depth as the other relays.
Page 1 and 2:
Cat. No. W266-E1-09 C200HW-SRM21-V1
Page 4:
Notice: OMRON products are manufact
Page 7 and 8:
viii TABLE OF CONTENTS SECTION 5 Sl
Page 9 and 10:
x Product Name Series Manual Name C
Page 11 and 12:
Application Considerations xii SUIT
Page 14 and 15:
PRECAUTIONS This section provides g
Page 16 and 17:
Operating Environment Precautions 4
Page 18 and 19:
Application Precautions 5 Pay caref
Page 20:
Conformance to EC Directives 6 6 Co
Page 23 and 24:
System Overview and Features Sectio
Page 25 and 26:
System Overview and Features Sectio
Page 27 and 28:
CompoBus/S System Configuration Sec
Page 29 and 30:
CompoBus/S System Configuration Sec
Page 31 and 32:
Compatible Devices Section 1-3 Cabl
Page 33 and 34:
Compatible Devices Section 1-3 Term
Page 35 and 36:
Compatible Devices Section 1-3 14 a
Page 37 and 38:
Compatible Devices Section 1-3 16 T
Page 39 and 40:
Compatible Devices Section 1-3 18 C
Page 41 and 42:
Startup Procedure Section 1-4 Conne
Page 44 and 45:
SECTION 2 CompoBus/S System Specifi
Page 46 and 47:
System Configuration Section 2-2 I/
Page 48 and 49:
System Configuration Section 2-2 Sl
Page 50 and 51:
System Configuration Section 2-2 Sl
Page 52 and 53:
Supplying Power to the Slaves Secti
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
System Configuration Using Water-re
Page 64 and 65:
I/O Response Time Characteristics S
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
SECTION 3 CompoBus/S System Wiring
Page 76 and 77:
Connector Installation (Special Fla
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
VCTF Cable Assembly Section 3-3 Bra
Page 88 and 89:
Master/Slave Connecting Cables Sect
Page 90 and 91:
Master/Slave Connecting Cables Sect
Page 92 and 93:
Operations Checklist Section 3-5 CS
Page 94 and 95:
SECTION 4 Master Unit Specification
Page 96 and 97:
C200HW-SRM21-V1 Master Unit for CS-
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
CS1W-SRM21 Master Unit for CS-serie
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
CJ1W-SRM21 Master Unit for CJ-serie
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
CQM1-SRM21-V1 Master Unit for CQM1
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
SRM1-C0@-V2 Master Control Units Se
Page 160 and 161:
SRM1-C0@-V2 Master Control Units Se
Page 162 and 163:
CPM2C-S Series CPM2C-S@@@C (-DRT) S
Page 164 and 165:
CPM2C-S Series CPM2C-S@@@C (-DRT) S
Page 166 and 167:
SECTION 5 Slave Specifications and
Page 168 and 169:
Remote Terminals Section 5-1 5-1 Re
Page 170 and 171:
Remote Terminals Section 5-1 Indica
Page 172 and 173:
Remote Terminals Section 5-1 The fo
Page 174 and 175:
Page 176 and 177:
Remote Terminals Section 5-1 CompoB
Page 178 and 179:
Remote Terminals Section 5-1 5-1-2
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Remote Terminals Section 5-1 Termin
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Remote Terminals Section 5-1 Slave
Page 204 and 205:
Page 206 and 207:
Remote Terminals Section 5-1 SRT@-M
Page 208 and 209:
Remote Terminals Section 5-1 Relay
Page 210 and 211:
Page 212 and 213:
Remote Terminals Section 5-1 BS+ BS
Page 214 and 215:
Remote Terminals Section 5-1 SRT@-R
Page 216 and 217:
Connector Terminals Section 5-2 Ite
Page 218 and 219:
Connector Terminals Section 5-2 Sla
Page 220 and 221:
Connector Terminals Section 5-2 Nod
Page 222 and 223:
Connector Terminals Section 5-2 The
Page 224 and 225:
Connector Terminals Section 5-2 Rei
Page 226 and 227:
Connector Terminals Section 5-2 Is
Page 228 and 229:
Connector Terminals Section 5-2 Dim
Page 230 and 231:
Connector Terminals Section 5-2 c.
Page 232 and 233:
Connector Terminals Section 5-2 Mou
Page 234 and 235:
Connector Terminals Section 5-2 5-2
Page 236 and 237:
Connector Terminals Section 5-2 Sla
Page 238 and 239:
Page 240 and 241:
Connector Terminals Section 5-2 The
Page 242 and 243:
Connector Terminals Section 5-2 Rei
Page 244 and 245:
Connector Terminals Section 5-2 Is
Page 246 and 247:
Page 248 and 249:
Connector Terminals Section 5-2 a.
Page 250 and 251:
Connector Terminals Section 5-2 Int
Page 252 and 253:
Connector Terminals Section 5-2 MIL
Page 254 and 255:
Connector Terminals Section 5-2 Com
Page 256 and 257:
Connector Terminals Section 5-2 Mou
Page 258 and 259:
Connector Terminals Section 5-2 Out
Page 260 and 261:
Page 262 and 263:
Connector Terminals Section 5-2 Wir
Page 264 and 265:
Connector Terminals Section 5-2 Ter
Page 266 and 267:
Page 268 and 269:
Connector Terminals Section 5-2 Inp
Page 270 and 271:
Connector Terminals Section 5-2 Ind
Page 272 and 273:
Connector Terminals Section 5-2 Wir
Page 274 and 275:
Connector Terminals Section 5-2 Ter
Page 276 and 277:
Page 278 and 279:
Connector Terminals Section 5-2 3.
Page 280 and 281:
Connector Terminals Section 5-2 fir
Page 282 and 283:
Remote I/O Modules Section 5-3 Outp
Page 284 and 285:
Remote I/O Modules Section 5-3 2. T
Page 286 and 287:
Remote I/O Modules Section 5-3 Prec
Page 288 and 289:
Remote I/O Modules Section 5-3 BD L
Page 290 and 291:
Water-resistant Terminals Section 5
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Sensor Terminals Section 5-5 5-5 Se
Page 310 and 311:
Sensor Terminals Section 5-5 Slave
Page 312 and 313:
Sensor Terminals Section 5-5 Hold/C
Page 314 and 315:
Sensor Terminals Section 5-5 The fo
Page 316 and 317:
Sensor Terminals Section 5-5 5-5-2
Page 318 and 319:
Sensor Terminals Section 5-5 DIP Sw
Page 320 and 321:
Sensor Terminals Section 5-5 Intern
Page 322 and 323:
Fiber Amplifier Communications Unit
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Analog Input Terminals Section 5-7
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Analog Output Terminals Section 5-8
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
I/O Link Units for CPM1A and CPM2A
Page 350 and 351:
I/O Link Units for CPM1A and CPM2A
Page 352 and 353:
I/O Link Units for CPM2C Section 5-
Page 354 and 355:
I/O Link Units for CPM2C Section 5-
Page 356 and 357: Sensor Amplifier Terminals Section
Page 372: Application Precautions Section 5-1
Page 375 and 376: Turning the Power ON Section 6-1 6-
Page 377 and 378: Checking Operations for CS-series,
Page 387 and 388: Checking Operations of CS-series an
Page 399 and 400: Checking Operations of CQM1 Master
Page 401 and 402: Checking Operations of CQM1 Master
Page 403 and 404: Checking Slave Operations Section 6
Page 405: Cleaning and Inspection Section 6-6
Page 409 and 410: Standard Models Appendix Compatible
Page 411 and 412: Standard Models Appendix Water-resi
Page 413 and 414: Standard Models Appendix Connectors
Page 415 and 416: Standard Models Appendix MIL-compat
Page 417 and 418: 396 DIP switch, 249 indicators, 249
Page 419 and 420: 398 Analog Input Terminals, 16, 389
Page 421 and 422: 400 Terminal-block Terminator speci
Page 423 and 424: 402 Revision History Revision code
Page 425: Authorized Distributor: Cat. No. W2
show all

OPERATION MANUAL CompoBus/S

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?