OPERATION MANUAL CompoBus/S

Standard Models Appendix
Connectors
Model Specifications
Branch Connector SCN1-TH4 Use this connector to branch a cable.
(Used with OMRON Flat Cable only.)
Extension Connector SCN1-TH4E Use this connector to extend the OMRON Flat Cable.
Connector Terminator SCN1-TH4T This connector has a built-in terminator.
(Used with OMRON Flat Cable only.)
Round Water-resistant Con- XS2W-D42@-@81-@ Use this connector to connect Water-resistant Terminals and Tnectors
with Cable (socket
joints.
and plug)
Can be used as a power supply cable (with the female socket
connected to the Water-resistant Terminal).
Can be used as an I/O cable for sensors that have connectors
(with the male plug connected to the Water-resistant Terminal, if
the product has a model number suffix “A”).
Connector with Cable XS2F-D42@-@80-@ A connector with cable used to connect Water-resistant Termi-
(female socket on one end)
nals to T-branch connectors.
Can be used as a power supply cable (with the female socket
connected to the Water-resistant Terminal) and the other end
wired to a commercially available terminal block.
Connector with Cable (male XS2H-D421-@80-A A connector with cable used to connect Water-resistant Termi-
plug on one end)
nals to I/O devices.
Can be used as an I/O cable (with the male plug connected to
the Water-resistant Terminal) and the other end wired to the I/O
device with loose wires.
Connector Socket Assembly XS2C-D4S7 A connector used to connect to the communications connectors
(female) (Crimp terminals/
or external power supply connectors of Water-resistant Terminals
Solder terminals)
or T-joint plugs.
Applicable cable dia.: 3 to 6 mm
Applicable conductor size: 0.18 to 0.75 mm 2
XS2C-D4@@ A connector used to connect to the external power supply connectors
of Water-resistant Terminals or T-joint plugs.
Applicable cable dia.: 3 to 6 mm
Applicable conductor size: 0.18 to 0.3 or 0.5 to 0.75 mm2 Connector Plug Assembly XS2G-D4S7 A connector used to connect to T-joint sockets.
(male) (Crimp terminals/Solder
terminals)
Applicable cable dia.: 6 to 8 mm
Applicable conductor size: 0.18 to 0.75 mm 2
XS2G-D4@@ A connector used to connect to I/O connectors of Water-resistant
Terminals or T-joint sockets.
Applicable cable dia.: 3 to 6 mm
Applicable conductor size: 0.18 to 0.3 or 0.5 to 0.75 mm 2
T-joint XS2R-D427-5 A joint used to T-branch a VCTF cable (e.g., a communications
cable or power supply cable).
Communications Connector FK-MCP1.5/6-STF- A communications connector for connecting CJ-series Master
(6-pin)
3.81
Units. Communications cables (BD H, BD L, BS+, BS–) and
communications power lines (BS +, BS–) can be connected
simultaneously. This connector has screwless terminals for signal
lines and connector lock screws.
MC1.5/6-STF-3.81 A communications connector for connecting CJ-series Master
Units. Communications cables (BD H, BD L, BS+, BS–) and
communications power lines (BS +, BS–) can be connected
simultaneously. This connector has screw terminals for signal
lines and connector lock screws.
Communications Connector BL3.5/6F (Product No. Communications cables, communications power supply and I/O
(Connector Terminals) 160668)
power supply connectors manufactured by Weidmuller Co., Ltd.
Shielded Terminator Plug
(Male)
SRS2-1 A shielded terminator plug used to connect to T-joints.
Terminal-block Terminator SRS1-T This terminal block has a built-in terminator. (Can be used with 2-
or 4-conductor VCTF cable and OMRON’s Special Flat Cable.)
392