cifX Communication Interfaces Real-Time Ethernet - Hilscher
cifX Communication Interfaces Real-Time Ethernet - Hilscher
cifX Communication Interfaces Real-Time Ethernet - Hilscher
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Getting Started <strong>cifX</strong> <strong>Communication</strong> <strong>Interfaces</strong> 59/274<br />
4.6.2 Steps how to replace the Hardware<br />
The following table describes the steps on how to replace a <strong>cifX</strong><br />
<strong>Communication</strong> Interface <strong>Real</strong>-<strong>Time</strong> <strong>Ethernet</strong> (Master and Slave) with and<br />
without Rotary Switch Slot Number (Card ID) as it is typical for many<br />
cases.<br />
# Step Description For detailed information<br />
see section<br />
1 Preparation<br />
Glue sticker on the<br />
front plate.<br />
Set the Slot Number<br />
(Card ID)<br />
(only device with a<br />
Rotary Switch)<br />
For CIFX 50-RE and CIFX 50E-RE:<br />
For CIFX 80-RE:<br />
For CIFX 100EH-RE\CUBE:<br />
Currently only CIFX 50-RE, CIFX 50E-RE and<br />
und CIFX 100EH-RE\CUBE:<br />
Important! At the replacement <strong>cifX</strong><br />
set the same Slot Number (Card<br />
ID) as at the previous <strong>cifX</strong>.<br />
Fix Front Plate Sticker at<br />
CIFX 50-RE and CIFX<br />
50E-RE<br />
Fix Front Plate Sticker at<br />
CIFX 80-RE<br />
Fix Front Plate Sticker at<br />
CIFX 100EH-RE\CUBE<br />
PCI and PCI Express:<br />
Setting Slot Number<br />
(Card ID)<br />
Page<br />
71<br />
78<br />
96<br />
67<br />
Device revisions equipped with a Rotary<br />
Switch Slot Number (Card ID) are listed<br />
separately in Table 2.<br />
Hardware: <strong>cifX</strong><br />
<strong>Communication</strong><br />
<strong>Interfaces</strong> <strong>Real</strong>-<strong>Time</strong><br />
<strong>Ethernet</strong><br />
17<br />
Set PCI 104 Slot<br />
Number.<br />
For <strong>cifX</strong> <strong>Communication</strong> <strong>Interfaces</strong> PCI 104:<br />
Set physical PCI 104 Slot Number.<br />
Replacing CIFX 104C-RE<br />
and CIFX 104C-RE-R<br />
Replacing CIFX 104C-<br />
RE\F and CIFX 104C-RE-<br />
R\F<br />
109,<br />
119<br />
For <strong>cifX</strong> <strong>Communication</strong> <strong>Interfaces</strong> PC/104:<br />
Set Starting Address<br />
and Interrupt<br />
Set Data Bus Width.<br />
Depending by the target system<br />
(motherboard), if so, set a Data Bus Width of<br />
8 bit or 16 bit. (Default jumper setting 16 Bit)<br />
<strong>cifX</strong> PC/104: Set Starting<br />
Address and Interrupt<br />
Device Drawing CIFX<br />
104-RE,<br />
Device Drawing CIFX<br />
104-RE-R,<br />
Device Drawing CIFX<br />
104-RE\F,<br />
Device Drawing CIFX<br />
104-RE-R\F<br />
124<br />
126,<br />
127,<br />
133,<br />
134<br />
<strong>cifX</strong> <strong>Communication</strong> <strong>Interfaces</strong> <strong>Ethernet</strong> | Installation, Operation and Hardware Description<br />
DOC060501UM30EN | Revision 30 | English | 2011-06 | Released | Public © <strong>Hilscher</strong>, 2006-2011