C55/C55i AT COMMAND SET Description Preliminary - Falcom

More documents

Recommendations

Info

C55/C55I AT COMMAND SET VERSION 1.00 Command Description This parameter setting determines the number of rings before automatic answering. Parameter Description (num)(&W)(&V) 000 (&F) automatic answering is disabled 001-255 enable automatic answering on the specified ring number Notes • This command works for MT data and fax calls. • Autoanswering of CSD data and fax calls is supported on ASC0/Mux1 only. • A CSD call will not be answered automatically if the module is in GPRS online mode. However, this is possible in GPRS command mode. The application can detect a call by evaluating the RING line and distinguish to change into GPRS command mode or stay in GPRS online mode until GPRS is available again. To answer, to reject or to wait for automatic answering the incoming call the application has to switch into GPRS command mode. • If is set to higher values, the calling party may terminate the call establishment before the call can be automatically answered. • The correlation between ATS7 and ATS0 is important. Example: ATS7=30 and ATS0=20 may not allow call establishment. • Setting is local to the interface. It is allowed to have different settings on different interfaces. In such cases the interface 'wins', which is idle and uses the smallest value. • ATSO write command is PIN protected. • The command ATS0 is also used as GPRS compatibility command to answer automatically to a network request for PDP context activation (for details see ATS0 for GPRS). So using ATS0= with n > 0, will perform a GPRS attach, if the ME is not already GPRS attached and if ME is configured to do this (see AT^SCFG, parameter ). If the GPRS attach fails (e.g. the network rejects the attach request), the write command returns with error, but the value of is changed anyway. The GPRS attach will not be performed on recalling a stored user profile with ATZ or on power up, if a n > 0 setting was stored in the user profile with AT&W. 6.12 ATS6 Set pause before blind dialing Syntax Read Command Response(s) ATS6? OK Write Command Response(s) ATS6= OK Reference(s) PIN V.25ter ○ ● ASC0 This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission. Page 110
C55/C55I AT COMMAND SET VERSION 1.00 Command Description No effect for GSM. Parameter Description (num)(&W)(&V) 000 (&F) ...255 6.13 ATS7 Set number of seconds to wait for connection completion Syntax Read Command Response(s) ATS7? OK Write Command Response(s) ATS7= OK Reference(s) PIN V.25ter ○ ● ASC0 Command Description This parameter setting determines the amount of time to wait for the connection completion when answering or originating a call. Parameter Description (num)(&W)(&V) no. of seconds to wait for connection completion 000...060 (&F) Notes • Values bigger than 60 cause no error, but will be set down to maximum value of 60. • In of ATS0 of the called party is set to higher values the call establishment may not be successful. • The correlation between ATS7 and ATS0 is important. Example: ATS7=30 and ATS0=20 may not allow call establishment. 6.14 ATS8 Set number of seconds to wait for comma dialing modifier Syntax Read Command Response(s) ATS8? Write Command ATS8= OK Reference(s) PIN Response(s) OK V.25ter ○ ● Command Description No effect for GSM. ASC0 This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission. Page 111
Page 1 and 2:
This document is available at HTTP:
Page 3 and 4:
C55/C55I AT COMMAND SET VERSION 1.0
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60: C55/C55I AT COMMAND SET VERSION 1.0
Page 89 and 90: XF55 AT COMMAND SET VERSION 1.00 4.
Page 109: C55/C55I AT COMMAND SET VERSION 1.0
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
show all

C55/C55i AT COMMAND SET Description Preliminary - Falcom

Create successful ePaper yourself

Delete template?

Save as template?