C55/C55i AT COMMAND SET Description Preliminary - Falcom

More documents

Recommendations

Info

C55/C55I AT COMMAND SET VERSION 1.00 • The read and write commands refer to the active audio mode. • specifies the amount of volume of each . The range of each is up to 65535, but will be suppressed to 32767. A value above = 65535 will cause an error. • The range of is up to 65535, but will be suppressed to 32767. A value above =65535 will cause an error. • Any change to takes effect in audio modes 2 to 6. • Audio mode 1 is fixed to =4. In this mode, any attempt to change or other parameters returns an error. • The value of is stored non-volatile when the ME is powered down with at^smso or reset with at+cfun=x,1. Any other parameters changed with at^snfo need to be saved with at^snfw for use after restart. See also at^snfd for details on restoring factory defaults. • The values of can also be changed with at^snfv and at+clvl. • CAUTION! When you adjust audio parameters avoid exceeding the maximum allowed level. Bear in mind that exposure to excessive levels of noise can cause physical damage to users! 14.10 AT ^ SNFPT Set progress tones Syntax Test Command AT^SNFPT=? Read Command AT^SNFPT? Write Command AT^SNFPT= Response(s) ^SNFPT: (list of supported s) OK Response(s) ^SNFPT: OK Response(s) OK Reference(s) PIN ASC0 SIEMENS ○ ● Command Description The write command controls the Call Progress Tones generated at the beginning of a mobile originated call setup. Parameter Description (num) Note • 0 1 (P) Disables Call Progress Tones Enables Call Progress Tones (audible tones shortly heard on the phone when ME starts to set up a call.) Please note that the setting is stored volatile, i.e. after restart or reset, the default value 1 will be restored. This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission. Page 268
C55/C55I AT COMMAND SET VERSION 1.00 14.11 AT ^ SNFV Set loudspeaker volume Syntax Test Command AT^SNFV=? Read Command AT^SNFV? Write Command AT^SNFV= Response(s) ^SNFV: (list of supported s) OK Response(s) ^SNFV: OK Response(s) OK ERROR +CME ERROR Reference(s) PIN ASC0 SIEMENS ○ ● Command Description The test command returns the supported values of the parameter . The read command returns the current value of parameter . The write command can be used to set the volume of the loudspeaker to the value addressed by . Parameter Description (num) The actual volume of each step is defined by the parameter , which can be set with at^snfo. 0...4 (p) Notes • The read and write commands refer to the active audio mode. • The write command works only in audio modes 2 to 6! • Any change to takes effect in audio modes 2 to 6. Nevertheless, the actual volume can be quite different, depending on the values of set in each mode. The only exception is audio mode 1 which is fixed to =4. • is stored non-volatile when the ME is powered down with at^smso or reset with at+cfun=1 ,1. is not stored by at^snfw. • can also be changed by at^snfo (chapter 14.9) and at+clvl (chapter 14.10). This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission. Page 269
Page 1 and 2:
This document is available at HTTP:
Page 3 and 4:
C55/C55I AT COMMAND SET VERSION 1.0
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
XF55 AT COMMAND SET VERSION 1.00 4.
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218: C55/C55I AT COMMAND SET VERSION 1.0
Page 267: C55/C55I AT COMMAND SET VERSION 1.0
show all

C55/C55i AT COMMAND SET Description Preliminary - Falcom

Create successful ePaper yourself

Delete template?

Save as template?