C55/C55i AT COMMAND SET Description Preliminary - Falcom

More documents

Recommendations

Info

C55/C55I AT COMMAND SET VERSION 1.00 presentation mode for this interface has to be configured with AT+CMER. The frequency of event report generation can be configured with AT command AT^SCFG. Refer to Call Status Information for further detail on the configuration options. • The additional read command allows to determine the event reporting mode which indicates whether the interface receives event report indications for the list of current calls. Mind that the URC will be displayed only if the URC presentation mode for the interface concerned has been configured with AT+CMER. Syntax Test Command Response(s) AT^SLCC=? OK Read Command Response(s) AT^SLCC? ^SLCC: OK Exec Command Response(s) AT^SLCC ^PSLCC: , , , , , [, , [, ]]] ^PSLCC: , , , , , [, , [, ]]] OK ERROR +CME ERROR Write Command Response(s) AT^SLCC=[] OK ERROR +CME ERROR: Reference(s) PIN SIEMENS ● ● ASC0 Unsolicited Result Code Unsolicited Call Status information if the list of current calls is empty: ^SLCC: if one or more calls are currently in the list: ^SLCC: , , , , , [,, [, ]] [^SLCC: , , , , , [, , [, ]]] [. . . ] ^SLCC: URC "^SLCC" displays the list of current calls as displayed with the execute command AT^SLCC. The list is displayed in the state it has at the time of display, not in the state it had when the signal was generated. The URC's occurrence indicates call status changes for any This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission. Page 118
C55/C55I AT COMMAND SET VERSION 1.00 of the calls in the list of current calls. Please refer to 6.1 and AT^SCFG for further information about the configuration of this URC. Event reporting can be enabled separately for each interface. Interface settings are saved with AT&W and can be displayed with AT&V. Additionally, the URC presentation mode for the interface must be configured with AT+CMER. Depending on the value of AT^SCFG setting , Indicator "^SLCC" will be issued (if configured with write command AT^SLCC and AT+CMER) � when a state transition ends in state "active" or in state "unknown" (if AT^SCFG setting ="restricted") � when any state transition (including transitions beginning or ending in state "unknown") occurs in the list of active calls, or when a traffic channel is established (if AT^SCFG setting ="verbose"). If multiple displays of identical list configurations occur, this happens because of short intermediate states of the list, that have already been overridden by new transitions and states. Thus, it is guaranteed that the configuration displayed is always the current configuration at the time of the last display. The list of active calls displayed with this URC will always be ^ terminated with an empty line preceded by prefix " SLCC:", in order to indicate the end of the list. Command Description The read command returns an indication whether event reporting is active for the current interface. The exec command returns a list of current calls of ME. If command is successful, but no calls are available, no information response is sent to TE. Use the write command to activate or deactivate event reporting for URC "^SLCC". Event reporting can be enabled separately for each interface. Interface settings are saved with AT&W and can be displayed with AT&V. Parameter Description (num) call identification number as described in GSM02.30 subclause 4.5.5.1; this number can be used in AT+CHLD command operations (num)(&W)(&V) 0 presentation of URC "^SLCC" disabled 1 presentation of URC "^SLCC" enabled (num) 0 mobile originated call (MOC) 1 mobile terminated call (MTC) (num) state of the call 0 active 1 held 2 dialing (MOC) 3 alerting (MOC) 4 incoming (MTC) This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission. Page 119
Page 1 and 2:
This document is available at HTTP:
Page 3 and 4:
C55/C55I AT COMMAND SET VERSION 1.0
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68: C55/C55I AT COMMAND SET VERSION 1.0
Page 89 and 90: XF55 AT COMMAND SET VERSION 1.00 4.
Page 117: C55/C55I AT COMMAND SET VERSION 1.0
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
show all

C55/C55i AT COMMAND SET Description Preliminary - Falcom

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?