DS7200V2-EXP - Simon Technologies

More documents

Recommendations

Info

DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 1003.9 Network CommunicationFirmware revision 2.10 or greater is required for network communication.The control panel can be configured to communicate over an Ethernet network. Reports can be sent over thisnetwork from the control panel to the ARC receiver. Remote programming can also be conducted over thisnetwork. A DX4020 Network Interface Module (NIM) is required for network communication. See NetworkInterface Module (DX4020) on page 35 for installation/configuration instructions.Use the following steps to configure the control panel for network communication:1. Enter an IP address for the ARC receiver [refer to IP Address 1 (2) for Destination 1 (2)].2. Set the Alternate Communications Options parameter to “5” (refer to page 101).3. Set the Network Interface Module Options parameter to “3” (refer to page 104).IP Address 1 (2) for Destination 1 (2)• Address:- IP Address 1, Destination 1: 0000 to 0031- IP Address 2, Destination 1: 0032 to 0063- IP Address 1, Destination 2: 0066 to 0097- IP Address 2, Destination 2: 0098 to 0129• Default: All zeroes (0)• Selections: 000.000.000.000 to 255.255.255.255Each routing destination can be configured as a phone number or an IP address. When entering an IP address,only the first 12 digits are used. For example, to enter an IP address of 172.30.1.101 into the Phone 1, Destination1 addresses, enter the following digits in the first 12 addresses: 1, 7, 2, 0, 3, 0, 0, 0, 1, 1, 0, 1.See Table 39 for entry selections.Table 39: IP Address Entry SelectionsDigit Enter at Keypad Digit Enter at Keypad1 [1] 6 [6]2 [2] 7 [7]3 [3] 8 [8]4 [4] 9 [9]5 [5] 0 [0] or [1][0]Remote Programming Callback Number• Address: 0181 to 0212• Default: All zeroes (0)• Selections: 000.000.000.000 to 255.255.255.255 (see Table 39)An IP address can be used to begin a remote programming session. See IP Address 1 (2) for Destination 1 (2) toenter an IP address. See Remote Programming Call Back Number on page 54 for more information.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 101Format for Destination 1 (2)• Address:- Format for Destination 1: 0064- Format for Destination 2: 0130• Default: 2 (Contact ID)• Selections:- 2 = Contact ID- 3 = SIA 300- 4 = Basic Pager- 6 = BSIA Fast Format- 7 = Personal Dialing Format- 11 = SIA 300 with Text BlocksIf network communication is enabled, the control panel automatically selects Contact ID as the reporting format.Contact ID only supports four-digit account numbers. This results in the control panel automatically truncatingaccount numbers to four digits.Alternate Communication Options• Address:- IP Address 1, Destination 1: 3506- IP Address 2, Destination 1: 3514- IP Address 1, Destination 2: 3522- IP Address 2, Destination 2: 3530• Default: 0• Selections: 0, 1, 3, 5, 7Enter This Data Digit to Select OptionsAlternate Communication Options 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15No Alternate Communication •Enable Alternate Communication • • • •Enable Anti-Replay • •Use ARC Acks • •Reserved• Enable Alternate Communication: Select this option to enable network communication. You must enter atleast one IP address as a routing destination. See IP Address 1 (2) for Destination 1 (2) on page 100 for moreinformation.• Enable Anti-Replay: Anti-replay prevents unauthorized messages from being sent to the Alarm ReceivingCenter (ARC) and being recognized as having originated from the control panel. Select this option to use theanti-replay procedure. To use this option, make sure “Include IP Address” is enabled.• Use ARC Acks: If this option is enabled, the control panel waits for an acknowledgment (Ack) from the ARCbefore sending a second message. If this option is disabled, the control panel waits approximately 120 sec.between sending messages (disable only for special applications).Bosch Security Systems, Inc. | 2/09 | 4998153893-03
Page 1 and 2:
DS7200V2-EXPENInstallation GuideDS7
Page 3 and 4:
DS7200V2-EXP | Installation Guide |
Page 5 and 6:
Page 7 and 8:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
P3LEDENABLEP2P6P1DS7200V2-EXP | Ins
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
. election, core spondingTosngsngan
Page 50 and 51: DS7200V2-EXP | Installation Guide |
Page 136: Bosch Security Systems, Inc.130 Per
show all

DS7200V2-EXP - Simon Technologies

Create successful ePaper yourself

Delete template?

Save as template?