DS7200V2-EXP - Simon Technologies

More documents

Recommendations

Info

DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 66Area Name Text• Address:- Area 1 Name: 1394 to 1425- Area 2 Name: 1458 to 1489- Area 3 Name (DS7240V2 only): 1522 to 1553- Area 4 Name (DS7240V2 only): 1586 to 1617• Default:- Area 1: Area 1 Name Text- Area 2: Area 2 Name Text- Area 3 (DS7240V2 only): Area 3 Name Text- Area 4 (DS7240V2 only): Area 4 Name Text• Selections: See Key/Character selection chartAll control panel text is programmed from the textkeypad in a special text-programming mode. See TextEntry Addresses on page 46 for text programminginstructions.Enter up to 16 characters to describe each area.Area Idle Text• Address:- Area 1 Idle Text: 1426 to 1457- Area 2 Idle Text: 1490 to 1521- Area 3 Idle Text (DS7240V2 only): 1554 to 1585- Area 4 Idle Text (DS7240V2 only): 1618 to 1649• Default: Not ReadyKeyCharacter0 + - 0 * / \ [ ] = > < # §1 Space . 1 ? ! , @ _ & ~ : ; " ( ) ' ¿ ¡ % £ $ ¥2 A B C a b c 2 Å Ä Ã å ä á à â ã α β Ç ç3 D E F d e f 3 É Æ ë é è ê æ Δ Φ δ ε4 G H I g h I 4 ï í î ì Γ γ η ι5 J K L j k l 5 Λ κ λ6 M N O m n o 6 Ö ö Ñ ñ Ø Õ ø ó ò ô õ Ω μ ν ω7 P Q R S p q r s 7 Π Σ π ρ σ8 T U V t u v 8 Ü ü ú ù û Θ Υ θ τ υ9 W X Y Z w x y z 9 ÿ Ξ Ψ ξ χ ψ ζ* Moves to the address before the text block.# Moves to the address after the text block.A Moves cursor to the previous character position intext block.C Moves cursor to the next character position in textblock.The following keys are not used in text programmingand produce an error tone when pressed: [On], [Off],[Perimeter Only], [No Entry], [Bypass], [System• Selections: See Key/Character selection chart (above)All control panel text is programmed from the text keypad in a special text-programming mode. See Text EntryAddresses on page 46 for text programming instructions.This parameter provides 16 characters of programmable text for each area displayed when the system is idle (noalarms, no troubles, system disarmed).If the “Don’t Show Zone Status on Keypads” option is not enabled in the Keypad # Options parameter (page 71),the text keypad displays “OK for All On” or “OK for Perimeter” across the second line. This indicates that allzones are normal and the system is ready to arm All On or Perimeter Only. If a controlled zone is faulted, thearea idle text for this zone’s assigned area replaces the “OK for All On/OK for Perimeter” message.If a zone not configured for Perimeter Only arming is faulted, “OK for Perimeter” replaces “OK for All On” onthe text keypad’s display. The system might be armed Perimeter Only, but cannot be armed All On until thefaulted zone is restored.If the “Don’t Show Zone Status on Keypads” option is enabled, the area idle text displays continuously on thesecond line when the keypad is idle (even if a zone is faulted).If the “Don’t Show Zone Status on Keypads” option is selected, the default Area Idle Text (“NotReady”) should be changed. See Text Entry Addresses on page 46 for text entry instructions.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 673.4 User Interface3.4.1 PIN Configuration/Installer PINA Personal Identification Number (PIN) is a unique number issued at the time of installation of each system.This PIN is required to operate the system (arm/disarm, test system, initiate functions, etc.). The PIN is not thesame as the account number.PIN Length• Address: 0379• Default: 4 (4 digits long)• Selections: 3 to 7 (3 digits min; 7 digits max)This parameter determines the number of digits in a PIN. All user PINs and the Installer PIN follow this length.If the PIN length is shortened after PINs are entered, duplicate PINs could be created (for example,PINs 1235 and 1238 would both become 123).User Tamper Options• Address: 0380• Default: 0• Selections: 0 to 3Enter This Data Digit to Select OptionsUser Tamper Options 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15No User Tamper Options •User Tamper {156} Reports Enabled • •User Tamper Activates Burg Alarm Output • •ReservedReservedA user tamper event is:- A user entering a PIN that is not in the system (the user must enter the invalid PIN the number of timesshown in User Tamper Retry Count on page 68).- A user entering a PIN that is in the system but does not have the authority for the desired function.• User Tamper Reports Enabled: If enabled, this option ties User Tamper {156} reports and user tamperactivated alarm outputs to the keypad’s area. If only the “User Tamper Reports Enabled” option is selectedand there is a user tamper event, the text keypad where the event occurs shows “Keypad locked!”• User Tamper Activates Burg Alarm Output: If the burglary alarm output (steady alarm output) is selectedand there is a user tamper event, the text keypad where the user tamper occurred shows “Keypad locked!”Other text keypads in the area show “Usr Tamper Alarm, Enter PIN to silence.” During the time the keypadis locked out, any key pressed produces an error tone (for text and LED keypads). Selecting the “User TamperActivates Burg Alarm Output” option specifically activates output functions 1|8, 1|9, 1|10, and 8|8. See Table34 on page 87 for descriptions of these output functions.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
Page 1 and 2:
DS7200V2-EXPENInstallation GuideDS7
Page 3 and 4:
DS7200V2-EXP | Installation Guide |
Page 5 and 6:
Page 7 and 8:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17: DS7200V2-EXP | Installation Guide |
Page 32 and 33: P3LEDENABLEP2P6P1DS7200V2-EXP | Ins
Page 48 and 49: . election, core spondingTosngsngan
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136:
Bosch Security Systems, Inc.130 Per
show all

DS7200V2-EXP - Simon Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?