DS7200V2-EXP - Simon Technologies

DS7200V2-EXP | Installation Guide | 1. Introduction EN | 81.4.7 Alarm Event MemoryThe system uses alarm event memory to store alarmevents for each area. You can view the area alarmevents at a keypad assigned to the area. The controlpanel clears the area’s alarm event memory and startsstoring new alarm events when you arm the area.Alarm events are permanently stored in the controlpanel’s history log.1.4.8 History LogThe system stores 254 events from all areas in its eventlog.Events can be stored even if the control panel does notsend a report for them. You can view the log at a textkeypad, print it locally using the DX4010i/DX4010RS-232 Serial Interface Module and a serial printer, orupload it to the Remote Programming Software (RPS).1.4.9 Wireless (RF) DevicesThe control panel supports a variety of wireless sensordevices, which can be included in the 40-zonemaximum.1.5 Control Panel AssemblyYou should receive the following parts:Documentation Pack• DS7200V2 Installation Guide (this document)(P/N: 4998153893)• DS7200V2 Expert Programming Guide(P/N: 4998153891)• System Worksheet (P/N: 4998153887)• Release Notes (P/N: 4998153890)• User’s Guide (P/N: 4998153894)Assembly• Control Panel Assembly• Red Battery Lead (P/N: 47720B)• Black Battery Lead (P/N: 47721B)• 2.2 k EOL Resistors (16 total)• 3.65 k EOL Resistors (8 total)• Tamper Switches1.6 Listings and Approvals• • This product fulfills the requirements ofEN 50131-1, 50131-2, CLC/TS 50131-31.7 System Options1.7.1 Arming Devices• DS7445i LED Keypad: LED keypad that displaysup to 16 zones.• DS7445V2 LED Keypad: LED keypad in newfaceplate design.• DS7447E LCD (Text) Keypad: Text keypad thatdisplays system information and programmabletext.• DS7447V2 LCD (Text) Keypad: Text keypad innew faceplate design.• Door Access Control Module (DACM): TheDACM grants or restricts access to a door using akeypad/credential reader, a Request to Exit (REX)input, and/or a door contact. Each DACMsupervises one door.1.7.2 Data Bus Devices• DX2010 Input Expander: Provides 8 additionalinput loops. The DS7240V2 supports up to 5modules; the DS7220V2 supports up to 3 modules.Also available: DX2014 (DX2010 with AE20 ABSplastic enclosure).• DX3010 Octo-Output Expander: Provides 8independent, programmable Form “C” relayoutputs. The DS7240V2 supports up to 2 modules;the DS7220V2 supports 1 module.• DX3020 Module: The DX3020 is an X-10Interface Module. It can emulate up to 2 DX3010Octo-Output Expanders. One allowed per system.• DX4010i RS-232 Serial Interface Module: DTERS-232 serial interface module that provides aconnection point to the system for serial devicessuch as a printer. Can also be used to create aremote programming direct connection with RPS.It does not occupy a control panel address whenused this way. One allowed per system• DX4010 RS-232 Serial Interface Module:Provides a connection point to the system for serialdevices such as a printer. Can also be used tocreate a remote programming direct connectionwith RPS. It does not occupy a panel address whenused this way. One allowed per system.• DX4020 Network Interface Module: Provides bidirectionalcommunication over an Ethernetnetwork. Can also be used for remoteprogramming sessions with RPS. One allowed persystem. Firmware revision 2.10 or greater isrequired to use the DX4020.Bosch Security Systems, Inc. | 2/09 | 4998153893-03