DS7200V2-EXP - Simon Technologies

More documents

Recommendations

Info

DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 543.2.3 Phone and RPS ConfigurationUse the parameters in this section to configure the telephone and Remote Programming Software (RPS) features.Phone Line Options• Address: 0131• Default: 0• Selections: 0 to 3, 8 to 11Enter This Data Digit to Select OptionsPhone Line Options 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15No Phone Line Options •Do Not Wait for Dial Tone • • • •“R” Function/Three-way Calling • • • •ReservedPhone Line Fault Requires Reset • • • •This parameter consists of three options for the physical phone line.• Do Not Wait for Dial Tone: If this option is enabled, the control panel waits three sec after going off-hookand then starts dialing. If this option is disabled, the control panel waits up to seven sec for a dial tone. Thecontrol panel dials when it detects the dial tone.• “R” Function/Three-way Calling: If this option is enabled, the control panel’s “R” function/three-waycalling feature is enabled. The phone company must enable this feature on the control panel’s telephone line.• Phone Line Fault Requires Reset: If this option is enabled and a phone line fault occurs, the troublecondition (keypad trouble message and/or tone) continues until the [System Reset] key is pressed (fix thephone line fault first). If this option is disabled and a phone line fault occurs, the trouble condition clearsautomatically when the phone line fault is corrected. This option also applies to the Alternate CommunicationPath Fault Control Input. See “24-Hour Control Input Zone Function Types” in the DS7200V2 ExpertProgramming Guide (P/N: 4998153891) for more information.Remote Programming Call Back Number• Address: 0181 to 0212• Default: All zeroes (0)• Selections: See Table 22The control panel dials this phone number or IP address to begin a RPS remote programming session. SeeNetwork Communication on page 100 for complete network communication programming instructions. Firmwarerevision 2.10 or greater is required for network communication.There are three ways to use this phone number (or IP address):1. RPS calls the control panel, which answers and determines it is RPS calling, then it hangs up and calls RPSback.2. When a user presses [#][4][3], the control panel calls RPS using the phone number (or IP address) enteredhere.3. The control panel can be programmed to call this phone number (or IP address) automatically at test reporttime (see Automatic Test {137} Report Options on page 59 for more information).When entering phone numbers, use “10” ([1][0] from the keypad) to dial “0”; enter “0” to terminate thephone number. This does not apply when entering an IP address.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 55RPS Answer Ring Count, Answering Machine Bypass• Address: 0213• Default: 7 (rings)• Selections:- 0 = Control panel does not answer phone- 1-13 = Ring Count- 14 = Answering Machine Bypass 1- 15 = Answering Machine Bypass 2The ring count sets the number of rings the control panel waits before picking up and seizing the phone line for aremote programming session, or for remote arming with a telephone (see Arming Options 1 on page 61).The control panel does not answer the phone for remote programming or remote arming with telephone whenthis parameter is set to zero (0).This ring count is used for any control panel arming state, armed or disarmed.The Answering Machine Bypass function can be restricted to only operate when the system is armed All On orPerimeter Only (see Arming Options 1 on page 61). When the Answering Machine Bypass function is restricted toonly operate when the system is armed All On or Perimeter Only, the control panel does not answer the phonefor a remote arming session when it is disarmed (Off). However, [#][4][3] still initiates a remote programmingsession.Answering Machine Bypass 11. Call the premises; let the phone ring no more than two (2) times. Then hang up/disconnect the remoteprogrammer.2. Wait at least eight (8) sec to call back, but call back within 45 sec.3. The control panel then picks up after the first ring.Answering Machine Bypass 21. Call the premises; let the phone ring no more than four (4) times. Then hang up/disconnect the remoteprogrammer.2. Wait at least eight (8) sec to call back, but call back within 45 sec.3. The control panel then picks up after the first ring.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
Page 1 and 2:
DS7200V2-EXPENInstallation GuideDS7
Page 3 and 4: DS7200V2-EXP | Installation Guide |
Page 32 and 33: P3LEDENABLEP2P6P1DS7200V2-EXP | Ins
Page 48 and 49: . election, core spondingTosngsngan
Page 104 and 105:
DS7200V2-EXP | Installation Guide |
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136:
Bosch Security Systems, Inc.130 Per
show all

DS7200V2-EXP - Simon Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?