DS7200V2-EXP - Simon Technologies

More documents

Recommendations

Info

DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 104Network Interface Module Options• Address: 3541• Default: 0• Selections: 0 to 3Enter This Data Digit to Select OptionsNetwork Interface Module Options 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15No Alternate Communication •Enable Alternate Communication • •Include IP Address • •ReservedReserved• Enable Alternate Communication: Select this option to supervise the connection between the control paneland the network interface module (DX4020). The network interface module’s DIP switch address must be setto 134. Do not select this option if there is no network interface module connected to the system.• Include IP Address: Select this option to use the IP address entered in IP Address 1 (2) for Destination 1 (2)(see page 100) instead of the IP address stored in the DX4020 for network communication. Select “EnableAlternate Communication” in Alternate Communication Options (refer to page 101) for the appropriate IPaddress. Select this option when using a DX4020. Do not select this option when using a DX4010i.3.10 DACM ConfigurationThe control panel supports up to 8 DACMs. However, each DACM added to the system replaces onekeypad. If 8 DACMs are added, you cannot add a keypad. For full system control, make sure at leastone text keypad is included in the system.For complete installation, programming, addressing, and operation instructions, see the documentationsupplied with the DACM.Configuring a DACM into the control panel is a three-step process:1. Using Table 30 on page 79, assign the DACM’s door contact as a location. For example, DACM #1’s doorcontact will be assigned to Location #5.a. Enter “6” at Address 0726 for the device type.b. Assign a zone function and enter it in Address 0727.c. Assign an area to the DACM in Address 0728. Each DACM’s door contact can only use onelocation.d. Repeat the area assignment in Keypad #/Door Access Control Module (DACM) Area Options. Forexample, if you selected Area 1 for Address 0728, then you must enter “9” in Address 0679. Thisaddress is for Keypad/DACM #1. “9” identifies the device as a DACM #1 in Area 1.e. Assign a zone number in Addresses 0729-0730 if the zone number must be different than thelocation number.2. Enter the location number in DACM Location Assignment. For this example, enter “0” in Address 3546, and“5” in Address 03547. This assigns the control panel’s Location #5 to DACM #1.3. Assign global options in Address 3562 (see DACM Global Options on page 106). The entry you make hereaffects all DACMs connected to the control panel.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 105Keypad/Door Access Control Module (DACM) Area Options• Address:- Keypad/DACM 1: 0679- Keypad/DACM 2: 0681- Keypad/DACM 3: 0683- Keypad/DACM 4: 0685- Keypad/DACM 5: 0687- Keypad/DACM 6: 0689- Keypad/DACM 7: 0691- Keypad/DACM 8: 0693• Default:- Keypad/DACM 1: 1 (Device is a keypad/DACM assigned to Area 1)- Keypads/DACMs 2 to 8: 0 (No keypad/DACM assigned)• Selections: 0 to 4, 9 to 12Enter This Data Digit to Select OptionsKeypad/DACM Area Options 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15Keypad/DACM not assigned (disabled) •Assign Keypad/DACM to Area 1 • •Assign Keypad/DACM to Area 2 • •Assign Keypad/DACM to Area 3 (DS7240V2 only) • •Assign Keypad/DACM to Area 4 (DS7240V2 only) • •Device is a Keypad • • • •Device is a DACM • • • •This parameter identifies the device connected to the control panel’s Data Bus (Addresses 1 to 8) as a DACM, andassigns the DACM to an area.The control panel supervises the connection to the DACM. If it fails to communicate with the control panel, thecontrol panel sends a “DBus Missing” {125} report.DACM Location Assignment• Address:- DACM 1: 3546 to 3547- DACM 2: 3548 to 3549- DACM 3: 3550 to 3551- DACM 4: 3552 to 3553- DACM 5: 3554 to 3555- DACM 6: 3556 to 3557- DACM 7: 3558 to 3559- DACM 8: 3560 to 3561• Default: 0,0• Selections:- DS7240V2: 0,0 to 4,0- DS7220V2: 0,0 to 2,4A DACM door contact can occupy any location in the control panel. Use this parameter to assign a control panellocation to a DACM door contact.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
Page 1 and 2:
DS7200V2-EXPENInstallation GuideDS7
Page 3 and 4:
DS7200V2-EXP | Installation Guide |
Page 5 and 6:
Page 7 and 8:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
P3LEDENABLEP2P6P1DS7200V2-EXP | Ins
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
. election, core spondingTosngsngan
Page 50 and 51:
Page 52 and 53:
Page 54 and 55: DS7200V2-EXP | Installation Guide |
Page 136: Bosch Security Systems, Inc.130 Per
show all

DS7200V2-EXP - Simon Technologies

Create successful ePaper yourself

Delete template?

Save as template?