DS7200V2-EXP - Simon Technologies

More documents

Recommendations

Info

DS7200V2-EXP | Installation Guide | 2. System Installation and Setup EN | 38You can use either one of the Aux Power (-) terminalsand either one of the 12 VDC (+) terminals whenconnecting devices to the control panel.Figure 59: DACM to Control Panel Wiring1346571- DACM2- Control Panel3- Wire Harness (supplied with DACM)4- Green (G) wire5- Yellow (Y) wire6- Black (-) wire7- Red (+) wire2You can use either one of the Aux Power (-) terminalswhen connecting to the control panel.Do not tie the black (-) output to earthground when using any external powersupply. A ground fault condition is reportedif black (-) is grounded.Figure 60: DACM to Control Panel Wiring(External Power Supply)17(+) (-)86BATT+BATT-BATT+BATT-1- DACM2- Control Panel3- Wire Harness (supplied with DACM)4- Green (G) wire5- Yellow (Y) wire6- Black (-) wire7- Red (+) wire8- External 12 VDC power supply32.10.3 DACM SupervisionThe control panel supervises communication to theDACM. If it fails to communicate with the DACM, itsends a “DBus Missing” {125} report.452Bosch Security Systems, Inc. | 2/09 | 4998153893-03
DS7200V2-EXP | Installation Guide | 2. System Installation and Setup EN | 392.11 System Power UpThe system shows a trouble upon any power-upbecause the date and time settings are missing. Thistrouble remains until these settings are made.To reduce the occurrence of false alarmsupon panel power-up (or restoration ofpower after a complete loss of primary andsecondary power), the control panelignores all zone faults for approximately 60sec while the devices stabilize.2.12 System Status LEDFigure 61 shows the location of the control panel’ssystem status LED. Table 19 shows the LED’s responseto system conditions.Figure 61: System Status LED2.13 Installer KeypadA text keypad can be configured as an InstallerKeypad.This keypad is not intended for permanent installationand must remain with the installer/service technician.Use the color-coded keypad wire assembly suppliedwith the control panel (P/N: 15-04298-0000) to connectthe Installer Keypad to the control panel’s Aux/Datapins. See Figure 62.Figure 62: Installer Keypad to Control PanelWiring12 361AUXILIARYSTATUSRR14 5Bat+Bat-BATT+BATT-ALRM+PO1A BPO1 SELECTTSMK+L-1 COM L-2 L-3 COM L-4 L-5 COM L-6 L-7 COM L-81- Control panel system status LEDTable 19: System Status LED OperationT11- DS7447E/DS7447V2 Text Keypad terminalblock2- Red (+) wire3- Black (-) wire4- Green (G) data wire5- Yellow (Y) data wire6- Control panel boardConditionSystem NormalBattery MissingAC MissingPhone RingingPhone Line Seized(control panel usingphone line)Shut Down (systemvoltage below 10.2VDC)LED ResponseOn for 50 ms, off for 1 sec.Off for 200 ms, on for 1 sec.Off for 200 ms, on for 200 ms,off for 200 ms, on for 1 sec.Flickers for 1 sec. As each ringis detected.On solid.Off for 200 ms, on for 200 ms,off 200 ms, on 200 ms, off 200ms, on for 1 sec.The Installer Keypad must be set toAddress 0 (set MODE to OFF) and theInstaller Switch must be closed to use theInstaller Keypad.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
Page 1 and 2: DS7200V2-EXPENInstallation GuideDS7
Page 3 and 4: DS7200V2-EXP | Installation Guide |
Page 32 and 33: P3LEDENABLEP2P6P1DS7200V2-EXP | Ins
Page 48 and 49: . election, core spondingTosngsngan
Page 88 and 89:
DS7200V2-EXP | Installation Guide |
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136:
Bosch Security Systems, Inc.130 Per
show all

DS7200V2-EXP - Simon Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?