DS7200V2-EXP - Simon Technologies

More documents

Recommendations

Info

DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 643.3 Area Wide ParametersThe parameters in this section configure the control panel’s areas. Each area has 16 characters of programmabletext for an area name and 16 characters of programmable area idle text, which appear on the text keypad display.The DS7240V2 supports up to four areas. The DS7220V2 supports up to two areas.All control panel text is programmed from the text keypad in a special text-programming mode. See Text EntryAddresses on page 46 for text programming instructions.Area # Account Number• Address/Default: See Table 26• Selections: 0 to 15 (see Table 27)Table 26: Account Number Addresses/DefaultsAreaAccount # for RoutingDestination 1Account # for RoutingDestination 2Default Account #(for both destinations)1 Address 0276 to 0281 Address 0286 to 0291 10, 10, 10, 10, 0, 02 Address 0298 to 0303 Address 0308 to 0313 10, 10, 10, 10, 0, 03 (DS7240V2 only) Address 0320 to 0325 Address 0330 to 0335 10, 10, 10, 10, 0, 04 (DS7240V2 only) Address 0342 to 0347 Address 0352 to 0357 10, 10, 10, 10, 0, 0Table 27: Account Number Entry SelectionsFor this Selection Press this Key For this Selection Press this Key0 10 8 81 1 9 92 2 B 113 3 C 124 4 D 135 5 E 146 6 F 157 7 Terminate 0Each area uses the account number entered here to report to the ARC receiver. Different account numbers can beprogrammed for two routing destinations. See Routing Destinations on page 49 for a complete description of howthe control panel directs reports to the routing destinations.Account numbers can contain up to six (6) digits. If less than four digits are entered, the control panel adds zerosto the end to make a four-digit account number.The control panel automatically truncates the account number to the maximum length supported by that format.See Control Panel Events and Reporting Formats on page 107 for a complete description of the reporting formatsavailable to the control panel.One account number digit occupies each address. Use a zero (0) to terminate the account number entry if it is lessthan six digits in length.For example, to set an account number of 1234, enter 1 2 3 4 0 (0 = Terminate).Use “10” ([1][0] from the keypad) to enter “0.” Use “0” to terminate the account number.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 65Area # Opening {89-96}/Closing {42-67} Reporting Options• Address:- Area 1: 0296- Area 2: 0318- Area 3 (DS7240V2 only): 0340- Area 4 (DS7240V2 only): 0362• Default: 1• Selections: 0, 1, 3, 5, 7, 9, 11, 13, 15Enter This Data Digit to Select OptionsArea # Open/Close Reporting Options 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15No Open or Close Reports for Area # •Open/Close Reports (for All On) for Area # Enabled • • • • • • • •Restrict Open/Close Reports; Open after Alarm, Closeon Force ArmOpen/Close Reports for Perimeter Only (and Partial On)Mode – Must also select Open/Close Reports (for AllOn)• • • •• • • •1 Second Bell Test on Closing Rpt Acknowledgement • • • •• Open/Close Reports for Area # Enabled: If enabled, this option configures Opening/Closing reports foreach area. This also includes the report for the Extend Auto Closing {21} event. Opening {89 to 96} andClosing {42 to 67} reports must be enabled at the system level. Opening and Closing reports are also enabledby authority level. Reporting must also be enabled at the system level (see Global Reporting Options on page57).• Restrict Open/Close Reports; Open From Alarm, Close on Force Arm: If this option is enabled, thecontrol panel only sends opening reports when the user disarms the system after an alarm and when BellTime has expired. The control panel only sends closing reports when a zone is force-armed. Force arming isset by authority level and by zone function configuration.Enabling the “Restrict Open/Close Reports” option overrides the “First Area to Open/Last Area toClose Reporting” option. See Arming Options 2 on page 62 for more information on the “RestrictOpen/Close Reports” option.• Open/Close Reports for Perimeter Only Mode: If this option is enabled, the control panel sends closingreports when users arm the system Perimeter Only. If any zones are bypassed, bypass reports are also sent.The control panel sends opening reports when users disarm the system. Perimeter Only arming is set byauthority level and by Zone Function configuration.• 1 Second Bell Test on Closing Ack: If this option is enabled, outputs assigned to Alarm Output Functions1|8, 1|9, 1|10, and 8|8 activate for one second. See Function, Output ## on page 87 for output functiondescriptions.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
Page 1 and 2:
DS7200V2-EXPENInstallation GuideDS7
Page 3 and 4:
DS7200V2-EXP | Installation Guide |
Page 5 and 6:
Page 7 and 8:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15: DS7200V2-EXP | Installation Guide |
Page 32 and 33: P3LEDENABLEP2P6P1DS7200V2-EXP | Ins
Page 48 and 49: . election, core spondingTosngsngan
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136:
Bosch Security Systems, Inc.130 Per
show all

DS7200V2-EXP - Simon Technologies

Create successful ePaper yourself

Delete template?

Save as template?