DS7200V2-EXP - Simon Technologies

More documents

Recommendations

Info

DS7200V2-EXP | Installation Guide | 2. System Installation and Setup EN | 24If you need to power the DX2010 with an external 12VDC power supply, wire it as shown in Figure 30.Figure 30: DX2010 to Control Panel Wiring(External Power Supply)12372.6.4 DX2010 Auxiliary Output WiringThe DX2010 can provide 12 VDC at up to 100 mAfrom the Auxiliary Output (-) OUT (+) terminals topower external devices such as motion detectors. SeeFigure 31.Figure 31: DX2010 Auxiliary Output Wiring1+OUT- TMPR R B G Y 1 COM56(+) (-)4+OUT-TMPR R B G Y 1 COM1- DX2010 Module2- Green (G) data wire3- Yellow (Y) data wire4- Black (-) wire5- Red (+) wire6- External 12 VDC power source7- Control panel boardBATT+BATT-Do not tie the black (-) output to earthground when using an external powersupply. A ground fault condition is reportedif black (-) is grounded.3241- DX2010 Module2- Motion detectors, photo beams, etc.3- Black (-) wire4- Red (+) wireThe following maximum wire lengths applywhen wiring the DX2010’s auxiliary outputto remotely powered devices, such asPIR’s and smoke detectors:−−15 m (49.2 ft) for 0.8 mm (#22 AWG)wire.30 m (98.4 ft) for 1.2 mm (#18 AWG)wire.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
DS7200V2-EXP | Installation Guide | 2. System Installation and Setup EN | 252.6.5 DX2010 Tamper Input WiringEach DX2010 module provides an input for tamperdevices. The tamper input is in addition to the zonesensor loops. Supervising an enclosure tamper does notoccupy a zone. A fault on the tamper input is reportedas a tamper event to which the Data Bus address theDX2010 is set.The tamper input can monitor external NormallyClosed (N/C) tamper switches when wired as shown inFigure 32. The tamper circuit must be closed to provideproper Input Expander tamper supervision to thecontrol panel. Do not use an EOL resistor.Use either the tamper input or the on-board tamperswitch. Both cannot be used simultaneously.Figure 33: DX2010 No Tamper1+OUT- TMPR R B G Y 1 COMFigure 32: DX2010 Tamper Input Wiring1+OUT- TMPR R B G Y 1 COM21- DX2010 Module2- Tamper Jumper2.6.6 DX2010 Tamper-Wired Zone WiringFor tamper-wired sensor loop configuration, wire asshown in Figure 34.Figure 34: DX2010 Tamper-Wired Zone Wiring21- DX2010 Module2- External tamper switchThe DX2014 configuration includes a tamper spring.Do not use the DX2010 TMPR input in the DX2014configuration.The DX2010’s on-board tamper switch cannot be usedwhen it is mounted inside the control panel’s enclosure(wire the tamper input as shown in Figure 33 if installedin the control panel’s enclosure).If neither the tamper input nor the on-board tamperswitch is used, a wire must be placed as shown in Figure33.11 COM 233 COM 4 5 COM 6 7 COM 812 21- Tamper contact2- 2.2 kΩ EOL resistors3- Alarm contacts (programmable for eitherNormally Open or Normally Closed)Bosch Security Systems, Inc. | 2/09 | 4998153893-03
Page 1 and 2: DS7200V2-EXPENInstallation GuideDS7
Page 3 and 4: DS7200V2-EXP | Installation Guide |
Page 32 and 33: P3LEDENABLEP2P6P1DS7200V2-EXP | Ins
Page 48 and 49: . election, core spondingTosngsngan
Page 74 and 75:
DS7200V2-EXP | Installation Guide |
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136:
Bosch Security Systems, Inc.130 Per
show all

DS7200V2-EXP - Simon Technologies

Create successful ePaper yourself

Delete template?

Save as template?