DS7200V2-EXP - Simon Technologies

More documents

Recommendations

Info

DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 88Table 34: Output Function Types (continued)Digit 1 Digit 2 Function Type Description0 11 Exit Delay, Entry Delay, Chime Output activates at the start of Exit Delay or Entry Delay. For Steady orPulse modes, the output remains activated until Entry or Exit Delay ends.The output also activates whenever a Chime zone is faulted. The outputdoes not activate on Chime if Chime Tone is turned off.0 12 Phone Line Fail Output activates when a Phone Line Fail condition is detected. ForSteady or Pulse modes, the output remains activated until the condition iscleared. This output works independently of Phone Line FaultResponse Options (page 56).0 13 Ack Received (any report) Output activates when the acknowledgement for any report is received.For Steady or Pulse modes, [System Reset] resets. This output type isevent-driven. See Mode (Steady, Pulse, One Shot), Output ## on page92 for more information.0 14 AC Fail Output activates when a AC Fail condition is detected. For Steady orPulse modes, the output remains activated until the condition is cleared.0 15 Low or Missing Battery Output activates when a control panel Low or Missing Battery conditionoccurs. For Steady or Pulse modes, the output remains activated until thecondition is cleared.1 0 PO 2 (on-board) SirenSupervision FailOutput activates when a Siren Supervision Fail condition is detected. ForSteady or Pulse modes, the output remains activated until the condition iscleared and [System Reset] is pressed.1 1 Sensor Trouble Monitor Output activates when a Sensor Trouble Monitor condition is detected inconjunction with the selection made for the Sensor Monitor Time setting.For Steady or Pulse modes, the output remains activated until the SensorMonitor Trouble condition is cleared.1 2 Duress, [#][4][7] (reset) resets Output activates whenever a Duress PIN is entered. For Steady or Pulsemodes, the output remains activated until user presses [System Reset].1 3 User Tamper, [#][4][7] (reset)resets1 4 Arming Beeps (forkeyswitch/RF arming)1 5 Bell Time – Starts on anyAlarm Event. PIN entry Stops.Activates on Bell Test.Output activates on a User Tamper event. For Steady or Pulse modes,the output remains activated until user presses [System Reset].Disarm/All On/Perimeter Only/Partial On Beeps for keyswitch/RF arming.1=Off, 2=All, 3=Perimeter Only. Mode and Time parameters do notapply. This function works in conjunction with Address 1039 (See“Global Output Options” in the DS7200V2 Expert ProgrammingGuide (P/N: 4998153891)). Available for on-board outputs only.Output activates on any alarm event. Entering PIN terminates Bell Time.For Steady and Pulse modes, the output remains activated for theduration programmed in the Bell Time parameter.1 6 Strobe Activates on Bell Time or output function as programmed. See “StrobeOutput Type Options” in the DS7200V2 Expert Programming Guide(P/N: 4998153891). PIN entry resets the function.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 89Table 34: Output Function Types (continued)Digit 1 Digit 2 Function Type Description1 7 Silent Alarm Activated by alarm on non-fire zones programmed for No Alarm Output.Follows Bell Time for Steady and Pulse modes. PIN stops. The followingconditions activate Silent Alarm:- ABC Key programmed for Fire or Emergency and no Alarm Output- RF Keyfob programmed for Fire or Emergency and no Alarm Output- A zone programmed for Fire or Fire with Verify and no Alarm Output- Any zone not programmed for Invisible Panic that is programmed for noAlarm Output- Any armed zone programmed as a controlled type that goes fromSupervised to Missing and programmed for no Alarm Output- Any armed keyswitch programmed for no Alarm Output that goes fromSupervised to Missing or Short to Missing- Any zone programmed for Swinger Count and Swinger Count for AlarmOutput that reaches its programmed value1 8 Alarm – All On, Perimeter Only,and Partial On Arming, Non-fire24 hour alarms1 9 Alarm – Perimeter Only andPartial On Arming Modes, Nonfire24 hour alarms1 10 Alarm –Controlled zones, 24-hrzones (Fire and Non-Fire)Activated by alarm on zone when All On, Perimeter Only, and Partial OnArmed, or by alarm on Non-fire 24 hour zone, and by user/installer ‘BellTest’. Follows Bell Time for Steady and Pulse modes. PIN resets. Followsprogramming for ‘Alarm’ output types.Activated by alarm on zone when Perimeter Only, and Partial On Armed,or by alarm on Non-fire 24 hour zone, and by user/installer ‘Bell Test’.Follows bell time for Steady and Pulse modes. PIN resets.Follows programming ‘Alarm’ output types.Activated by alarm on zone when All On, Perimeter Only, and Partial OnArmed, or by alarm on Fire and Non-fire 24 hour zone, and byuser/installer ‘Bell Test’. Follows bell time for Steady and Pulse modes.Pulses in Temporal Code 3 format for Fire alarms only. PIN resets.Off-board outputs cannot provide output in Temporal Code 3 format(only on-board outputs). Off-board outputs provide a steady output.Follows programming for ‘Alarm’ output types. Temporal Code 3 forFire alarms only.1 11 Fire Alarm Activated by alarm on Fire zone, and by user/installer ‘Bell Test’. FollowsBell Time. Pulses in Temporal Code 3 format. Mode and Time parametersdo not apply. PIN resets. Off-board outputs cannot provide output inTemporal Code 3 format (only on-board outputs). Off-board outputsprovide a steady output. Follows programming for ‘Alarm’ outputtypes.1 12 Fire Alarm, Latching Activated by alarm on Fire zone, and by user/installer ‘Bell Test’. Does notpulse in Temporal Code 3 format. Mode and Time parameters do notapply. [#][4][7] resets. Follows programming for ‘Alarm’ output types.1 13 Fire Verification/Reset Normally on. Turns off on activation to reset smoke detectors. Verificationfor Fire Verification Zone Function type and [System Reset] activateoutput for approximately 15 sec. Mode and Time parameters do notapply. Used for 4-wire smoke detectors.1 14 System Trouble Activates on any System Trouble. Resets when all system troubles areclear.1 15 [O] Key (Trapezoid Key on RFKey Fob)Activates when Trapezoid Key on RF Keyfob is pressed. [System Reset]resets. Pressing O (trapezoid) key again also resets output when OutputMode is set to Toggle. This output type is event-driven. See Mode(Steady, Pulse, One Shot), Output ## on page 92 for more information.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
Page 1 and 2:
DS7200V2-EXPENInstallation GuideDS7
Page 3 and 4:
DS7200V2-EXP | Installation Guide |
Page 5 and 6:
Page 7 and 8:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
P3LEDENABLEP2P6P1DS7200V2-EXP | Ins
Page 34 and 35:
Page 36 and 37:
Page 38 and 39: DS7200V2-EXP | Installation Guide |
Page 48 and 49: . election, core spondingTosngsngan
Page 136: Bosch Security Systems, Inc.130 Per
show all

DS7200V2-EXP - Simon Technologies

Create successful ePaper yourself

Delete template?

Save as template?