<strong>DS7200V2</strong>-<strong>EXP</strong> | Installation Guide | 3. Control Panel Programming EN | 106DACM Global Options• Address: 3562• Default: 0• Selections: 0, 1, 3-5, 7Enter This Data Digit to Select OptionsDACM Global Options 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15No DACM Global Options Selected •Enable Arming Confirmation • • • •Any User Confirms Arming • •Use Tamper-Wired Processing • • •ReservedThis is a global parameter that affects all DACMs connected to the control panel.• Enable Arming Confirmation: If this option is enabled, verifying a user at the DACM reader during ExitDelay cancels the remaining Exit Delay time and arms the control panel immediately. Only the user whostarted the arming process can confirm arming. If this option is disabled, verifying a user at the DACM readerduring Exit Delay cancels the arming process (the system does not arm).• Any User Confirms Arming: If this option is enabled, any user can confirm system arming. If this option isdisabled, only the user who started the arming process can confirm arming. This option only applies when“Enable Arming Confirmation” is selected.• Use Tamper-Wired Processing: If this option is enabled, an open door reports as faulted (the zone assignedto the DACM functions as a tamper-wired zone). If this option is disabled, an open door reports as shorted(the zone assigned to the DACM functions as a single EOL zone).3.11 Test the SystemAfter finishing the installation and programming of the control panel, make a complete functional test of thesystem. Test the control panel and all devices for proper operation. Test after you first program the control paneland after any subsequent programming session. If you test a device and the control panel does not respond, theremight be a problem with the device, the wiring, a module setting, or the programming for the zone.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
<strong>DS7200V2</strong>-<strong>EXP</strong> | Installation Guide | 4. Reference Materials EN | 1074. Reference Materials4.1 Control Panel Events and Reporting FormatsThe following table includes each control panel event, the description for each event as it appears in the controlpanel log, the reports sent for each event, the zone types linked to the event, and the RPS Event Alert Groupnumber. The RPS Event Group numbers also correspond with the Personal Dialing Format Event Groupnumbers. See Personal Dialing Format on page 50 for more information.The last column, Status Reports, indicates System Status events. An “R” indicates that reports for the event followthe System Status routing. An “S” indicates that the event follows the System Status Swinger Count. Systemreports do not include an Area number; they use the account number for Area 1.If the control panel is configured for network communication, reports are sent using the Contact ID format.The event numbers shown in the following table are the same numbers that show up on a pager for eachcorresponding report.Table 40: Control Panel Events and Reporting FormatsEventEvent as shown inControl Panel LogSIA ReportContact IDReportEvent DescriptionZone TypesLinked to EventRPSEventGroupStatusReport01 AC Fail AT AC Trouble 301 AC Loss AC Power to panel interrupted. 12 R S02 AC Restore AR AC Restoral 301 AC Loss AC Power to panel restored. 12 R S03 Alarm,Tamper TA Tamper Alarm 137 Tamper Alarm, Tamper Zone Type. 4-Tamper 304* Alarm,Emergency QA EmergencyAlarm101 PersonalEmergencyAlarm, Emergency Zone Type orABC key programmed foremergency response. [Q] button.05* Alarm,Panic PA Panic Alarm 120 Panic Alarm, Panic-Visible Zone Type. [Q]button.06* Alarm,Invisible HA Holdup Alarm 120 Panic Alarm, Panic- Invisible Zone Typeor ABC key programmed for panicresponse. [Q] button.07 Alarm,24-hr Burg BA BurglaryAlarm08 Alarm,Cntrl,Dly BA BurglaryAlarm09 Alarm,Cntrl BA BurglaryAlarm10 Cross,Tamper BM BurglaryAlarm CrossZone11 Cross,Emergency BM BurglaryAlarm CrossZone12 Cross,Panic BM BurglaryAlarm CrossZone13 Cross,Invisible BM BurglaryAlarm CrossZone133 24 HrSafeAlarm, Burglary Zone Type.134 Entry/Exit Alarm, Delay 1 or Delay 2 ZoneType.130 Burglary Alarm, Keyswitch or Follower orInstant Zone Types.137 Tamper Alarm, Tamper Zone Type withCross Zone Option selected.101 PersonalEmergencyAlarm, Emergency Zone Type withCross Zone Option selected.120 Panic Alarm, Panic-Visible Zone Typewith Cross Zone Option selected.120 Panic Alarm, Panic- Invisible Zone Typewith Cross Zone Option selected.5- Emergency 36- Visible Panic 37-Invisible Panic 38- Burglary315 - Door11- E/E Delay 1 312- E/E Delay 210- Keyswitch 313- Follower14- Instant4-Tamper 35- Emergency 36- Visible Panic 37-Invisible Panic 3* Keypad [A], [B], or [C] keys report as Zones 100, 101, and 102. The [Q] button on a keyfob reports as UserNumber +200. See the <strong>DS7200V2</strong> Expert Programming Guide (P/N: 4998153891) for information on [Q] buttonprogramming.Bosch Security Systems, Inc. | 2/09 | 4998153893-03