DS7200V2-EXP - Simon Technologies

DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 66Area Name Text• Address:- Area 1 Name: 1394 to 1425- Area 2 Name: 1458 to 1489- Area 3 Name (DS7240V2 only): 1522 to 1553- Area 4 Name (DS7240V2 only): 1586 to 1617• Default:- Area 1: Area 1 Name Text- Area 2: Area 2 Name Text- Area 3 (DS7240V2 only): Area 3 Name Text- Area 4 (DS7240V2 only): Area 4 Name Text• Selections: See Key/Character selection chartAll control panel text is programmed from the textkeypad in a special text-programming mode. See TextEntry Addresses on page 46 for text programminginstructions.Enter up to 16 characters to describe each area.Area Idle Text• Address:- Area 1 Idle Text: 1426 to 1457- Area 2 Idle Text: 1490 to 1521- Area 3 Idle Text (DS7240V2 only): 1554 to 1585- Area 4 Idle Text (DS7240V2 only): 1618 to 1649• Default: Not ReadyKeyCharacter0 + - 0 * / \ [ ] = > < # §1 Space . 1 ? ! , @ _ & ~ : ; " ( ) ' ¿ ¡ % £ $ ¥2 A B C a b c 2 Å Ä Ã å ä á à â ã α β Ç ç3 D E F d e f 3 É Æ ë é è ê æ Δ Φ δ ε4 G H I g h I 4 ï í î ì Γ γ η ι5 J K L j k l 5 Λ κ λ6 M N O m n o 6 Ö ö Ñ ñ Ø Õ ø ó ò ô õ Ω μ ν ω7 P Q R S p q r s 7 Π Σ π ρ σ8 T U V t u v 8 Ü ü ú ù û Θ Υ θ τ υ9 W X Y Z w x y z 9 ÿ Ξ Ψ ξ χ ψ ζ* Moves to the address before the text block.# Moves to the address after the text block.A Moves cursor to the previous character position intext block.C Moves cursor to the next character position in textblock.The following keys are not used in text programmingand produce an error tone when pressed: [On], [Off],[Perimeter Only], [No Entry], [Bypass], [System• Selections: See Key/Character selection chart (above)All control panel text is programmed from the text keypad in a special text-programming mode. See Text EntryAddresses on page 46 for text programming instructions.This parameter provides 16 characters of programmable text for each area displayed when the system is idle (noalarms, no troubles, system disarmed).If the “Don’t Show Zone Status on Keypads” option is not enabled in the Keypad # Options parameter (page 71),the text keypad displays “OK for All On” or “OK for Perimeter” across the second line. This indicates that allzones are normal and the system is ready to arm All On or Perimeter Only. If a controlled zone is faulted, thearea idle text for this zone’s assigned area replaces the “OK for All On/OK for Perimeter” message.If a zone not configured for Perimeter Only arming is faulted, “OK for Perimeter” replaces “OK for All On” onthe text keypad’s display. The system might be armed Perimeter Only, but cannot be armed All On until thefaulted zone is restored.If the “Don’t Show Zone Status on Keypads” option is enabled, the area idle text displays continuously on thesecond line when the keypad is idle (even if a zone is faulted).If the “Don’t Show Zone Status on Keypads” option is selected, the default Area Idle Text (“NotReady”) should be changed. See Text Entry Addresses on page 46 for text entry instructions.Bosch Security Systems, Inc. | 2/09 | 4998153893-03