DS7200V2-EXP - Simon Technologies

More documents

Recommendations

Info

DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 983.8 Data Bus Device ParametersThe following parameters configure devices that connect to the control panel’s Data Bus. See the DS7200V2 ExpertProgramming Guide (P/N: 4998153891) for all Data Bus device parameters.RF Receiver Options• Address: 1249• Default: 0• Selections: 0 to 15Enter This Data Digit to Select OptionsPremises RF Receiver Options 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15No RF Receiver Connected •RF Receiver 1 connected, set to Address 50 • • • • • • • •RF Receiver 2 connected, set to Address 51 • • • • • • • •Disable RF Loop Tamper • • • • • • • •Keyfobs Do Not Force Arm Faulted Zones • • • • • • • •• RF Receiver 1 Connected, Set Receiver to Address 50: Enable this option if RF Receiver 1 has beenconnected to the control panel. Set the RF receiver’s address to 50 (jumper setting OFF). See Adding RF IDCodes on page 41 for instructions. See RF Transmitters and Zone States on page 84 for details on RF transmittersand zone states.All status reports for the RF Receiver include the address. For example, if the cover is removed, Event {127}(DBus Tamper) is generated (the address is included in the report).• RF Receiver 2 Connected, Set Receiver to Address 51: Enable this option if RF Receiver 2 has beenconnected to the control panel. Set the RF receiver’s address to 51 (jumper setting ON). See Adding RF IDCodes on page 41 for instructions. See RF Transmitters and Zone States on page 84 for details on RF transmittersand zone states.All status reports for the RF Receiver include the address. For example, if the cover is removed, Event {127}(DBus Tamper) is generated (the address is included in the report).• Disable RF Loop Tamper: The RF3401E transmitter’s loop can be wired with a single 2.2 k EOL resistor, orit can be wired with dual 2.2 k EOL resistors. If this option is enabled, wire the RF3401E with a single 2.2 kEOL resistor. The loop can report as normal, shorted, or open. If this option is disabled, wire the RF3401E iswith dual 2.2 k EOL resistors. The loop can report as normal, shorted, faulted, or open.• Keyfobs Do Not Force Arm Faulted Zones: If this option is enabled, arming from a keyfob does not forcearm faulted zones. A faulted zone prevents the area from arming. If this option is disabled, arming from akeyfob does force arm faulted zones.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
DS7200V2-EXP | Installation Guide | 3. Control Panel Programming EN | 99RF Receiver Supervision Interval• Address: 1250• Default: 5 (24 h)• Selections:- 0 = No Supervision- 1 = 1 h- 2 = 2 h- 3 = 4 h- 4 = 12 h- 5 = 24 hRF transmitters (sensors) send a supervisory signal approximately once every 13 min. The RF receiver expects tohear this signal from every transmitter in the interval determined in this parameter. A “Missing” report is sent foreach device that the RF Receiver does not hear.Fire transmitters have a fixed supervision interval of 4 h.Bosch Security Systems, Inc. | 2/09 | 4998153893-03
Page 1 and 2:
DS7200V2-EXPENInstallation GuideDS7
Page 3 and 4:
DS7200V2-EXP | Installation Guide |
Page 5 and 6:
Page 7 and 8:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
P3LEDENABLEP2P6P1DS7200V2-EXP | Ins
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49: . election, core spondingTosngsngan
Page 50 and 51: DS7200V2-EXP | Installation Guide |
Page 136: Bosch Security Systems, Inc.130 Per
show all

DS7200V2-EXP - Simon Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?