DS7200V2-EXP - Simon Technologies

More documents

Recommendations

Info

DS7200V2-EXP | Installation Guide | 2. System Installation and Setup EN | 20Figure 20: 4-wire Smoke Detector (Single EOLResistor)2.4.2 Programmable Output 1 (PO 1)By default, PO 1 is the Bell output, and the PO 1SELECT jumper should be shorted. See Figure 21.Figure 21: PO 1 Wiring (PO 1 Jumper Shorted)PO1 SELECT11BATT+BATT-ALRM+PO1 SMKA B + L-1 COMPO1 SELECT651- Remove jumper plug from PO 1 SELECTjumper2- 2.2 kΩ EOL resistor3- EOL200 End-of-Line Module4- DS250 with MB4W Base5- AUX (+)6- AUX (-)2.4 On-board Output Setup2.4.1 OverviewThe control panel has four on-board programmableoutputs (PO 1 to PO 4).Programmable Output 2 (PO 2) can be configured as asupervised siren driver. See “Global Output Options”in the DS7200V2 Expert Programming Guide(P/N: 4998153891) for programming instructions.When programmed as a siren driver, PO 2 drawspower from the ALRM + terminal. When connected toa 4 Ω horn/speaker, PO 2 draws 380 mA of current.When connected to an 8 Ω horn/speaker, it draws330 mA of current. Use the appropriate current drawin your total alarm power calculation.432BATT+BATT-ALRM+PO1A B(+) (-)1- Short PO 1 SELECT jumper with jumper plug2- Audible notification appliancePO 1 can also be configured as an alarm power output(short PO 1 SELECT jumper). PO 1 operates as a drycontact, Normally Open relay with PO 1 SELECTjumper open. See Figure 22, and Figure 23 on page 21for details.SMK+L-12COMFigure 22: PO1 Dry Contact Wiring (No PO 1Jumper)ALRM+PO1A B(+) (+)(+) (-)2(-)SMK+L-111- Audible notification appliance2- DC power sourceBosch Security Systems, Inc. | 2/09 | 4998153893-03
DS7200V2-EXP | Installation Guide | 2. System Installation and Setup EN | 21Figure 23:PO 1 Positive Alarm Trigger WiringALRM+PO1A B(+)SMK+1- Audible notification appliance2.4.3 Programmable Outputs 2 to 4 (PO 2 toPO 4)PO 2 can be used with ALRM+ as a supervised sirendriver. Connect an approved 4 or 8 Ω speaker.Alternatively, PO 2 can sink up to 500 mA 12 VDC.See Figure 24.Figure 24: PO 2 to PO 4 WiringL-11If PO 1 to PO 4 do not provide the alarm output youexpect, do the following:Check the programming for Programmable Outputs inOutput Parameters on page 85.Check “Zone Function Configuration” in theDS7200V2 Expert Programming Guide (P/N: 4998153891)to verify the zones you are activating are programmedfor alarm output.2.5 RF3227E RF Receiver SetupFor complete installation instructions regarding theRF3227E Premises RF Receiver, see the RF3227EInstallation Guide (P/N: 4998122415).2.5.1 RF Receiver AddressingSet the RF3227E’s address by placing the addressjumper pin as shown in Figure 25.Remove power from the system and RFreceiver so that RF receiver addresschanges can take effect.Figure 25: RF3227E Address Jumper SettingsBATT+PO1 SELECT12BATT-ALRM+(+) (-)PO1A B1SMK+L-1COMADDRR B G Y31- Audible notification applianceIf PO 2 is configured as a supervised sirendriver (in combination with the ALRM +terminal), you must connect a 4 Ω or 8 Ωspeaker to PO 2 to clear the speakersupervision trouble.PO 3 and PO 4 can be configured for Alarm Output.These outputs can sink up to 500 mA 12 VDC each.Defaults for PO 2 to PO 4 are as follows:PO 2: 1|6 (Strobe)PO 3: 0|1 (armed: All, Perimeter Only, Partial On)PO 4: 2|13 (Ready to Arm)See Output Parameters on page 85 for programminginstructions.1- RF receiver address jumper pins2- RF Receiver #1 (Address 50) jumper plug OFF(default position)3- RF Receiver #2 (Address 51) jumper plug ONBosch Security Systems, Inc. | 2/09 | 4998153893-03
Page 1 and 2: DS7200V2-EXPENInstallation GuideDS7
Page 3 and 4: DS7200V2-EXP | Installation Guide |
Page 32 and 33: P3LEDENABLEP2P6P1DS7200V2-EXP | Ins
Page 48 and 49: . election, core spondingTosngsngan
Page 70 and 71:
DS7200V2-EXP | Installation Guide |
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136:
Bosch Security Systems, Inc.130 Per
show all

DS7200V2-EXP - Simon Technologies

Create successful ePaper yourself

Delete template?

Save as template?