Altivar 61 - error

[1.8 FAULT MANAGEMENT] (FLt-)
[4-20mA LOSS] (LFL-)
Code
Description
LFL2 Terminal display: [AI2 4-20mA loss]
Logic address: 7003 =16#1B5B Type: WORD (listing)
CANopen index: 2028/4 Read/write: R/WS
INTERBUS index: 5FBC/87 Factory setting: 0
DeviceNet path: 84/01/04
0=[Ignore] (nO): Fault ignored. This configuration is the only one possible if [AI2 min. value] (CrL2), see “CrL2”,
page 161, is not greater than 3 mA.
1=[Freewheel] (YES): Freewheel stop
2=[Per STT] (Stt): Stop according to configuration of [Type of stop] (Stt), see “Stt”, page 194.
4=[fallback spd] (LFF): Change to fallback speed, maintained as long as the fault persists and the run command
has not been removed.
5=[Spd maint.] (rLS): The drive maintains the speed at the time the fault occurred, as long as the fault persists and
the run command has not been removed.
6=[Ramp stop] (rMP): Stop on ramp
7=[Fast stop] (FSt): Fast stop
8=[DC injection] (dCI): DC injection stop
LFL3 Terminal display: [AI3 4-20mA loss]
Logic address: 7013 =16#1B65 Type: WORD (listing)
CANopen index: 2028/E Read/write: R/WS
INTERBUS index: 5FBC/8F Factory setting: 0
DeviceNet path:
84/01/0E
0=[Ignore] (nO): Fault ignored. This configuration is the only one possible if [AI3 min. value] (CrL3), see “CrL3”,
page 163, is not greater than 3 mA.
1=[Freewheel] (YES): Freewheel stop
2=[Per STT] (Stt): Stop according to configuration of [Type of stop] (Stt), see “Stt”, page 194.
4=[fallback spd] (LFF): Change to fallback speed, maintained as long as the fault persists and the run command
has not been removed.
5=[Spd maint.] (rLS): The drive maintains the speed at the time the fault occurred, as long as the fault persists and
the run command has not been removed.
6=[Ramp stop] (rMP): Stop on ramp
7=[Fast stop] (FSt): Fast stop
8=[DC injection] (dCI): DC injection stop
LFL4 Terminal display: [AI4 4-20mA loss]
Logic address: 7014 =16#1B66 Type: WORD (listing)
CANopen index: 2028/F Read/write: R/WS
INTERBUS index: 5FBC/90 Factory setting: 0
DeviceNet path:
84/01/0F
0=[Ignore] (nO): Fault ignored. This configuration is the only one possible if [AI4 min. value] (CrL4), see “CrL4”,
page 165, is not greater than 3 mA.
1=[Freewheel] (YES): Freewheel stop
2=[Per STT] (Stt): Stop according to configuration of [Type of stop] (Stt), see “Stt”, page 194.
4=[fallback spd] (LFF): Change to fallback speed, maintained as long as the fault persists and the run command
has not been removed.
5=[Spd maint.] (rLS): The drive maintains the speed at the time the fault occurred, as long as the fault persists and
the run command has not been removed.
6=[Ramp stop] (rMP): Stop on ramp
7=[Fast stop] (FSt): Fast stop
8=[DC injection] (dCI): DC injection stop
239