model 2704 controller installation and operation handbook - Soliton

More documents

Recommendations

Info

Digital Communications 2704 Controller 16. Chapter 16 Digital Communications 16.1. WHAT IS DIGITAL COMMUNICATIONS? Digital Communications (or ‘comms’ for short) allows the controller to communicate with a PC or a networked computer system. A choice of comms protocol is available and can be selected in configuration level. These are MODBUS (or JBUS), EIBisynch, and Profibus. Comms modules can be fitted which use RS232, RS485 or RS422 Transmission Standards. A full description of these standards is given in the 2000 series Communications Handbook, part number HA026230. Comms modules can be fitted into either or both of two positions referred to as the H slot and the J slot which correspond to the rear terminal connections, see also section 2.4. Both slot positions may be used at the same time. An example is, to allow a multi-drop connection between a number of controllers and a computer running, say, a SCADA package on one comms position, and a separate PC used for configuration purposes on the second comms position. In this example an RS485 module may be fitted for the multi-drop/SCADA requirement and RS232 in the second position for the single PC/configuration requirement. Note: When the controller is placed into Configuration Level it is taken ‘off line’ and placed into a standby state. In this state it no longer monitors or controls the plant. 16-2 Installation and Operation Handbook. Part No HA026502 Issue 1.0 Apr-00
2704 Controller Digital Communications 16.2. TO SET COMMUNICATIONS ADDRESS AND RESOLUTION Parameters in the Comms page allow you to set up the Address and Resolution. The operation of the H and J Modules is the same. Do This 1. From any display press as many times as necessary to access the page header menu This Is The Display You Should See Additional Notes 2. Press or to select ‘COMMS’ 3. Press to show Subheaders 4. Press or to select ‘H Module’ Digital communications modules may be fitted in either one or both positions. 5. Press to show the list of comms parameters. 6. Press again to select ‘Address’ Up to 254 addresses can be set in level 1 7. Press or to change the instrument address 8. Press to select further parameters 9. Press or to change a parameter value where applicable Choices are:- Full Integer Level 3 Modbus EIBisynch OR Profibus EI Bisynch (f ordered) Level 3 Read only Installation and Operation Handbook. Part No HA026502 Issue 1.0 Apr-00 16-3
Page 1 and 2:
2704 Controller Contents MODEL 2704
Page 3 and 4:
2704 Controller Contents 5. CHAPTER
Page 5 and 6:
2704 Controller Contents 7. CHAPTER
Page 7 and 8:
2704 Controller Contents 9.5.1. Int
Page 9 and 10:
2704 Controller Contents 13. CHAPTE
Page 11 and 12:
2704 Controller Contents 18. CHAPTE
Page 13 and 14:
2704 Controller Contents B. APPENDI
Page 15 and 16:
2704 Controller Contents LIST OF FI
Page 17 and 18:
2704 Controller Contents Figure 18-
Page 19 and 20:
2704 Controller Introduction 1. Cha
Page 21 and 22:
2704 Controller Introduction 1.2. W
Page 23 and 24:
2704 Controller Introduction ➃
Page 25 and 26:
2704 Controller Introduction 1.4.1.
Page 27 and 28:
2704 Controller Introduction 1.6. I
Page 29 and 30:
2704 Controller Installation 2. CHA
Page 31 and 32:
2704 Controller Installation 2.1.3.
Page 33 and 34:
2704 Controller Installation • Te
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
2704 Controller Installation 2.4. O
Page 41 and 42:
Page 43 and 44:
2704 Controller Installation I/O Mo
Page 45 and 46:
2704 Controller Installation Transd
Page 47 and 48:
Page 49 and 50:
2704 Controller Getting Started 3.
Page 51 and 52:
2704 Controller Getting Started 3.1
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
2704 Controller Getting Started 5.
Page 63 and 64:
Page 65 and 66:
2704 Controller Getting Started Wor
Page 67 and 68:
2704 Controller Getting Started Ins
Page 69 and 70:
HUMIDITY INPUT OPERS TIMER BLOCKS P
Page 71 and 72:
2704 Controller Access Levels 4. CH
Page 73 and 74:
2704 Controller Access Levels If a
Page 75 and 76:
2704 Controller The Summary Page 5.
Page 77 and 78:
2704 Controller Programmer Operatio
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
2704 Controller Digital Programmer
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
2704 Controller Alarm Operation 7.
Page 119 and 120:
2704 Controller Alarm Operation 7.2
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
2704 Controller Tuning 8. CHAPTER 8
Page 141 and 142:
2704 Controller Tuning 8.2. AUTOMAT
Page 143 and 144:
2704 Controller Tuning Typical auto
Page 145 and 146:
2704 Controller Tuning 8.4.3. To Vi
Page 147 and 148:
2704 Controller Tuning 8.5.1. Setti
Page 149 and 150:
2704 Controller Tuning 8.6. GAIN SC
Page 151 and 152:
2704 Controller Loop Set Up 9. CHAP
Page 153 and 154:
2704 Controller Loop Set Up 9.2. TO
Page 155 and 156:
2704 Controller Loop Set Up 9.2.2.
Page 157 and 158:
2704 Controller Loop Set Up 9.3. TO
Page 159 and 160:
2704 Controller Loop Set Up 9.4. CA
Page 161 and 162:
2704 Controller Loop Set Up 9.5. RA
Page 163 and 164:
2704 Controller Loop Set Up 9.6. OV
Page 165 and 166:
2704 Controller Loop Set Up 9.7. CO
Page 167 and 168:
2704 Controller Loop Set Up 9.8. OU
Page 169 and 170:
2704 Controller Loop Set Up 9.9. LP
Page 171 and 172:
2704 Controller Controller Applicat
Page 173 and 174:
2704 Controller Controller Applicat
Page 175 and 176: 2704 Controller Controller Applicat
Page 183 and 184: 2704 Controller Input Operators 11.
Page 195 and 196: 2704 Controller Totaliser, Timer. C
Page 209 and 210: 2704 Controller User Values 13. CHA
Page 211 and 212: 2704 Controller User Values 5. Pres
Page 213 and 214: 2704 Controller User Values 13.3. W
Page 215 and 216: 2704 Controller Analogue Operators
Page 221 and 222: 2704 Controller Logic Operators 15.
Page 223 and 224: 2704 Controller Logic Operators 15.
Page 225: 2704 Controller Digital Communicati
Page 229 and 230: 2704 Controller Standard IO 17. CHA
Page 231 and 232: 2704 Controller Standard IO 17.2. P
Page 233 and 234: 2704 Controller Standard IO 10. Pre
Page 235 and 236: 2704 Controller Standard IO 17.3. A
Page 237 and 238: 2704 Controller Standard IO To set
Page 239 and 240: 2704 Controller Standard IO 17.6. S
Page 241 and 242: 2704 Controller Module IO 18. CHAPT
Page 243 and 244: 2704 Controller Module IO 18.2. MOD
Page 245 and 246: 2704 Controller Module IO 18.3.1. D
Page 247 and 248: 2704 Controller Module IO 18.3.3. T
Page 249 and 250: 2704 Controller Module IO 18.3.6. P
Page 251 and 252: 2704 Controller Module IO 18.3.9. P
Page 253 and 254: 2704 Controller Module IO 18.3.11.
Page 255 and 256: 2704 Controller Module IO 18.4. MOD
Page 257 and 258: 2704 Controller Module IO [Units] I
Page 263 and 264: 2704 Controller Transducer Scaling
Page 277 and 278:
2704 Controller Diagnostics 20. CHA
Page 279 and 280:
2704 Controller Diagnostics Note 1.
Page 281 and 282:
2704 Controller Appendix A A. APPEN
Page 283 and 284:
2704 Controller Appendix A B. QUICK
Page 285 and 286:
2704 Controller Safety and EMC Info
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
2704 Controller Technical Specifica
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
show all

model 2704 controller installation and operation handbook - Soliton

Create successful ePaper yourself

Delete template?

Save as template?