model 2704 controller installation and operation handbook - Soliton

More documents

Recommendations

Info

Technical Specification 2704 Controller C.4. ANALOGUE INPUT No of inputs One fixed (Not isolated) Can be used with either floating or ground referenced transducers of low impedance. Input range -10V to +10V linear or 0 -20 mA with burden resistor of 100*. Calibration: ±(1.5mV + 0.1% of reading) Resolution: 0.9mV Drift: < ±(0.1mV + 0.006% of reading) per °C Input Impedance: 0.46MΩ (floating input), 0.23MΩ (ground referenced input) Isolation Not isolated from standard digital I/O . Differential type input with common mode range of + 42Vdc (the average voltage of the two inputs with respect to ‘Screen’ or ‘Common’ terminals should be within +42Vdc. CMRR : >110dB at 50/60Hz, >80dB at DC Functions Process variable, remote setpoint, power limit, feedforward, etc. C.5. ANALOGUE INPUT MODULE Allocation Up to 4 analogue input modules can be fitted in I/O slots 1,3,4 & 6 mV input 100mV range - used for thermocouple, linear mV source, or 0-20mA with 2.49Ω external burden resistor. Calibration: + 10µV + 0.2% of reading Resolution: 6µV Drift: < + 0.2µV + 0.004% of reading per O C Input impedance: >10MΩ, Leakage: 10MΩ, Leakage: 69KΩ Pt100 input 0 to 400ohms (-200°C to +850°C), 3 matched wires - up to 22* in each lead without errors. Calibration: ±(0.4°C + 0.15% of reading in °C) Resolution: 0.08°C Drift: < ±(0.015°C + 0.005% of reading in °C) per °C Bulb current: 0.3mA. Thermocouple Internal compensation: CJC rejection ratio >25:1 typical. CJ Temperature calibration error at 25 O C:
2704 Controller Technical Specification C.6. Allocation not isolated Digital inputs Digital outputs STANDARD DIGITAL I/O 1 digital input standard and 7 I/O which can be configured as inputs or outputs plus 1 changeover relay Voltage level : input active < 2Vdc, inactive >4Vdc Contact closure : input active 28kohms Open collector, 24Vdc at 40mA drive capability, requires external supply Contact rating 2A at 264Vac resistive Changeover relay Functions Refer to Chapter 17 Operations 1,000,000 operations with addition of external snubber C.7. DIGITAL INPUT MODULES Module type Triple contact input, Triple logic input Allocation Can be fitted into slots 1, 3, 4, 5 or 6 Contact closure Active 28kohms Logic inputs Current sinking : active 10.8Vdc to 30Vdc at 2.5mA inactive -3 to 5Vdc at
Page 1 and 2:
2704 Controller Contents MODEL 2704
Page 3 and 4:
2704 Controller Contents 5. CHAPTER
Page 5 and 6:
2704 Controller Contents 7. CHAPTER
Page 7 and 8:
2704 Controller Contents 9.5.1. Int
Page 9 and 10:
2704 Controller Contents 13. CHAPTE
Page 11 and 12:
2704 Controller Contents 18. CHAPTE
Page 13 and 14:
2704 Controller Contents B. APPENDI
Page 15 and 16:
2704 Controller Contents LIST OF FI
Page 17 and 18:
2704 Controller Contents Figure 18-
Page 19 and 20:
2704 Controller Introduction 1. Cha
Page 21 and 22:
2704 Controller Introduction 1.2. W
Page 23 and 24:
2704 Controller Introduction ➃
Page 25 and 26:
2704 Controller Introduction 1.4.1.
Page 27 and 28:
2704 Controller Introduction 1.6. I
Page 29 and 30:
2704 Controller Installation 2. CHA
Page 31 and 32:
2704 Controller Installation 2.1.3.
Page 33 and 34:
2704 Controller Installation • Te
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
2704 Controller Installation 2.4. O
Page 41 and 42:
Page 43 and 44:
2704 Controller Installation I/O Mo
Page 45 and 46:
2704 Controller Installation Transd
Page 47 and 48:
Page 49 and 50:
2704 Controller Getting Started 3.
Page 51 and 52:
2704 Controller Getting Started 3.1
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
2704 Controller Getting Started 5.
Page 63 and 64:
Page 65 and 66:
2704 Controller Getting Started Wor
Page 67 and 68:
2704 Controller Getting Started Ins
Page 69 and 70:
HUMIDITY INPUT OPERS TIMER BLOCKS P
Page 71 and 72:
2704 Controller Access Levels 4. CH
Page 73 and 74:
2704 Controller Access Levels If a
Page 75 and 76:
2704 Controller The Summary Page 5.
Page 77 and 78:
2704 Controller Programmer Operatio
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
2704 Controller Digital Programmer
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
2704 Controller Alarm Operation 7.
Page 119 and 120:
2704 Controller Alarm Operation 7.2
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
2704 Controller Tuning 8. CHAPTER 8
Page 141 and 142:
2704 Controller Tuning 8.2. AUTOMAT
Page 143 and 144:
2704 Controller Tuning Typical auto
Page 145 and 146:
2704 Controller Tuning 8.4.3. To Vi
Page 147 and 148:
2704 Controller Tuning 8.5.1. Setti
Page 149 and 150:
2704 Controller Tuning 8.6. GAIN SC
Page 151 and 152:
2704 Controller Loop Set Up 9. CHAP
Page 153 and 154:
2704 Controller Loop Set Up 9.2. TO
Page 155 and 156:
2704 Controller Loop Set Up 9.2.2.
Page 157 and 158:
2704 Controller Loop Set Up 9.3. TO
Page 159 and 160:
2704 Controller Loop Set Up 9.4. CA
Page 161 and 162:
2704 Controller Loop Set Up 9.5. RA
Page 163 and 164:
2704 Controller Loop Set Up 9.6. OV
Page 165 and 166:
2704 Controller Loop Set Up 9.7. CO
Page 167 and 168:
2704 Controller Loop Set Up 9.8. OU
Page 169 and 170:
2704 Controller Loop Set Up 9.9. LP
Page 171 and 172:
2704 Controller Controller Applicat
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
2704 Controller Input Operators 11.
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
2704 Controller Totaliser, Timer. C
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
2704 Controller User Values 13. CHA
Page 211 and 212:
2704 Controller User Values 5. Pres
Page 213 and 214:
2704 Controller User Values 13.3. W
Page 215 and 216:
2704 Controller Analogue Operators
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
2704 Controller Logic Operators 15.
Page 223 and 224:
2704 Controller Logic Operators 15.
Page 225 and 226:
2704 Controller Digital Communicati
Page 227 and 228:
2704 Controller Digital Communicati
Page 229 and 230:
2704 Controller Standard IO 17. CHA
Page 231 and 232:
2704 Controller Standard IO 17.2. P
Page 233 and 234:
2704 Controller Standard IO 10. Pre
Page 235 and 236:
2704 Controller Standard IO 17.3. A
Page 237 and 238:
2704 Controller Standard IO To set
Page 239 and 240:
2704 Controller Standard IO 17.6. S
Page 241 and 242:
2704 Controller Module IO 18. CHAPT
Page 243 and 244: 2704 Controller Module IO 18.2. MOD
Page 245 and 246: 2704 Controller Module IO 18.3.1. D
Page 247 and 248: 2704 Controller Module IO 18.3.3. T
Page 249 and 250: 2704 Controller Module IO 18.3.6. P
Page 251 and 252: 2704 Controller Module IO 18.3.9. P
Page 253 and 254: 2704 Controller Module IO 18.3.11.
Page 255 and 256: 2704 Controller Module IO 18.4. MOD
Page 257 and 258: 2704 Controller Module IO [Units] I
Page 263 and 264: 2704 Controller Transducer Scaling
Page 277 and 278: 2704 Controller Diagnostics 20. CHA
Page 279 and 280: 2704 Controller Diagnostics Note 1.
Page 281 and 282: 2704 Controller Appendix A A. APPEN
Page 283 and 284: 2704 Controller Appendix A B. QUICK
Page 285 and 286: 2704 Controller Safety and EMC Info
Page 291 and 292: 2704 Controller Technical Specifica
Page 293: 2704 Controller Technical Specifica
show all

model 2704 controller installation and operation handbook - Soliton

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?