model 2704 controller installation and operation handbook - Soliton

More documents

Recommendations

Info

Installation 2704 Controller 2.3.4. Analogue Input Connections The analogue input is supplied as standard and is intended to accept 0 to 10 Vdc from a voltage source. A milli-amp current source can be used by connecting a 100Ω resistor across terminals BA and BB. This input can be used as a remote setpoint input, remote setpoint trim or as a high level PV input to a control loop. This input is not isolated from the digital IO. Non-isolated Voltage Source (0 to 10V) BA BB BC + - If screened cable is used earth at the supply end Nonisolated 0 to 10Vdc source Non-isolated Current Source (0 - 20mA) (4 - 20mA) BA BB BC + - 100Ω If screened cable is used earth at the supply end Nonisolated current source Isolated Voltage Source (0 to 10V) BA BB BC + - Screen Isolated 0 to 10Vdc source Isolated Current Source (0 - 20mA) (4 - 20mA) BA BB BC + - 100Ω Screen Isolated current source Figure 2-7: Wiring Connections For Analogue Input 2-8 Installation and Operation Handbook Part No HA026502 Issue 1.0 Apr-00
2704 Controller Installation 2.3.5. I/O Expander (or Additional Digital Input) The I/O expander is used with the 2704 to allow the number of I/O points to be increased by a further 20 digital inputs and 20 digital outputs. Data transfer is performed serially via a two wire interface from instrument to expander. If the expander unit is not required it is possible to use terminals E1 & E2 as a secondary digital input. These terminals are not part of the digital I/O on terminals D1 to D8 and if used in this way connect a 2K2, ¼ W limiting resistor in series with the input, as shown in Figure 2-8. I/O expander connections E1 E2 Data transfer ƒ 20 Inputs Expander 20 Outputs … I/O expander connections E1 E2 Additional digital input if the expander is not used 2K2 + - Limits: -1V, +35V Figure 2-8: Wiring Connections for the I/O Expander Installation and Operation Handbook. Part No HA026502 Issue 1.0 Apr-00 2-9
Page 1 and 2: 2704 Controller Contents MODEL 2704
Page 3 and 4: 2704 Controller Contents 5. CHAPTER
Page 5 and 6: 2704 Controller Contents 7. CHAPTER
Page 7 and 8: 2704 Controller Contents 9.5.1. Int
Page 9 and 10: 2704 Controller Contents 13. CHAPTE
Page 11 and 12: 2704 Controller Contents 18. CHAPTE
Page 13 and 14: 2704 Controller Contents B. APPENDI
Page 15 and 16: 2704 Controller Contents LIST OF FI
Page 17 and 18: 2704 Controller Contents Figure 18-
Page 19 and 20: 2704 Controller Introduction 1. Cha
Page 21 and 22: 2704 Controller Introduction 1.2. W
Page 23 and 24: 2704 Controller Introduction ➃
Page 25 and 26: 2704 Controller Introduction 1.4.1.
Page 27 and 28: 2704 Controller Introduction 1.6. I
Page 29 and 30: 2704 Controller Installation 2. CHA
Page 31 and 32: 2704 Controller Installation 2.1.3.
Page 33 and 34: 2704 Controller Installation • Te
Page 35: 2704 Controller Installation 2.3.3.
Page 39 and 40: 2704 Controller Installation 2.4. O
Page 43 and 44: 2704 Controller Installation I/O Mo
Page 45 and 46: 2704 Controller Installation Transd
Page 49 and 50: 2704 Controller Getting Started 3.
Page 51 and 52: 2704 Controller Getting Started 3.1
Page 61 and 62: 2704 Controller Getting Started 5.
Page 65 and 66: 2704 Controller Getting Started Wor
Page 67 and 68: 2704 Controller Getting Started Ins
Page 69 and 70: HUMIDITY INPUT OPERS TIMER BLOCKS P
Page 71 and 72: 2704 Controller Access Levels 4. CH
Page 73 and 74: 2704 Controller Access Levels If a
Page 75 and 76: 2704 Controller The Summary Page 5.
Page 77 and 78: 2704 Controller Programmer Operatio
Page 87 and 88:
2704 Controller Programmer Operatio
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
2704 Controller Digital Programmer
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
2704 Controller Alarm Operation 7.
Page 119 and 120:
2704 Controller Alarm Operation 7.2
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
2704 Controller Tuning 8. CHAPTER 8
Page 141 and 142:
2704 Controller Tuning 8.2. AUTOMAT
Page 143 and 144:
2704 Controller Tuning Typical auto
Page 145 and 146:
2704 Controller Tuning 8.4.3. To Vi
Page 147 and 148:
2704 Controller Tuning 8.5.1. Setti
Page 149 and 150:
2704 Controller Tuning 8.6. GAIN SC
Page 151 and 152:
2704 Controller Loop Set Up 9. CHAP
Page 153 and 154:
2704 Controller Loop Set Up 9.2. TO
Page 155 and 156:
2704 Controller Loop Set Up 9.2.2.
Page 157 and 158:
2704 Controller Loop Set Up 9.3. TO
Page 159 and 160:
2704 Controller Loop Set Up 9.4. CA
Page 161 and 162:
2704 Controller Loop Set Up 9.5. RA
Page 163 and 164:
2704 Controller Loop Set Up 9.6. OV
Page 165 and 166:
2704 Controller Loop Set Up 9.7. CO
Page 167 and 168:
2704 Controller Loop Set Up 9.8. OU
Page 169 and 170:
2704 Controller Loop Set Up 9.9. LP
Page 171 and 172:
2704 Controller Controller Applicat
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
2704 Controller Input Operators 11.
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
2704 Controller Totaliser, Timer. C
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
2704 Controller User Values 13. CHA
Page 211 and 212:
2704 Controller User Values 5. Pres
Page 213 and 214:
2704 Controller User Values 13.3. W
Page 215 and 216:
2704 Controller Analogue Operators
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
2704 Controller Logic Operators 15.
Page 223 and 224:
2704 Controller Logic Operators 15.
Page 225 and 226:
2704 Controller Digital Communicati
Page 227 and 228:
2704 Controller Digital Communicati
Page 229 and 230:
2704 Controller Standard IO 17. CHA
Page 231 and 232:
2704 Controller Standard IO 17.2. P
Page 233 and 234:
2704 Controller Standard IO 10. Pre
Page 235 and 236:
2704 Controller Standard IO 17.3. A
Page 237 and 238:
2704 Controller Standard IO To set
Page 239 and 240:
2704 Controller Standard IO 17.6. S
Page 241 and 242:
2704 Controller Module IO 18. CHAPT
Page 243 and 244:
2704 Controller Module IO 18.2. MOD
Page 245 and 246:
2704 Controller Module IO 18.3.1. D
Page 247 and 248:
2704 Controller Module IO 18.3.3. T
Page 249 and 250:
2704 Controller Module IO 18.3.6. P
Page 251 and 252:
2704 Controller Module IO 18.3.9. P
Page 253 and 254:
2704 Controller Module IO 18.3.11.
Page 255 and 256:
2704 Controller Module IO 18.4. MOD
Page 257 and 258:
2704 Controller Module IO [Units] I
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
2704 Controller Transducer Scaling
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
2704 Controller Diagnostics 20. CHA
Page 279 and 280:
2704 Controller Diagnostics Note 1.
Page 281 and 282:
2704 Controller Appendix A A. APPEN
Page 283 and 284:
2704 Controller Appendix A B. QUICK
Page 285 and 286:
2704 Controller Safety and EMC Info
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
2704 Controller Technical Specifica
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
show all

model 2704 controller installation and operation handbook - Soliton

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?