z/VM: System Messages and Codes Š CP - z/VM - IBM

eal storage area of an operating system running under
z/VM.
System Action: The command is not executed;
system operation continues.
User Response: Reenter the command, using only
valid hexadecimal locations within the range of the
address space.
HCP161I END or ALL was specified or defaulted
and storage exceeds over maximum
dumpable address hexloc. Pages over
that address will not be dumped
Explanation: VMDUMP was requested to dump to the
end of configured storage, but the highest address that
VMDUMP can dump is X'7FFFEFFF'.
System Action: VMDUMP dumps storage up to that
limit. Processing continues.
User Response: None.
HCP162E Hexloc hexloc exceeds maximum
dumpable address hexloc and cannot
be dumped
Explanation: All or part of the specified range
exceeds the maximum address that VMDUMP can
process.
System Action: The command is not executed.
System operation continues.
User Response: Enter the command again using only
hexadecimal locations below the maximum address that
VMDUMP can process.
HCP163E STORE exceeds maximum register
Explanation: The STORE command has specified that
a number of operands are to be stored in contiguous
registers, and the number of operands specified would
place the store beyond the valid register range.
System Action: The system has stored up to, and
including, the highest register allowed for the store
function.
User Response: Verify that the store command was
entered correctly and that the beginning register was
correctly specified. If they were not, reissue the STORE
command, specifying the correct registers and
operands.
HCP164E Hexloc hexloc non-addressable storage
Explanation: The hexadecimal address specified with
the command is within a nonaddressable storage range.
System Action: The command is not executed;
system operation continues.
User Response: Reissue the command specifying a
valid hexadecimal address.
HCP167E The mask is invalid for the specified
data range.
Explanation: You issued the TRACE GPR command
specifying a DATA range and MASK value. When the
MASK value was ANDed with both values in the DATA
range, the lower limit of the resulting range was greater
than the upper limit.
System Action: The command is not executed;
system operation continues.
User Response: Reissue the command specifying a
valid mask.
HCP170E System name exceeds storage size;
{nnnnnnnnK|nnnnM} required
Explanation: The NSS (name) specified requires a
guest real storage size larger than that defined for the
virtual machine.
System Action: The command is not executed;
system operation continues.
User Response: Redefine the virtual machine storage
size using the DEFINE command, then reissue the
command with the required storage size.
HCP174E Paging I/O error; IPL failed
HCP161I HCP177E
Explanation: An I/O error occurred while the system
was attempting to read a page from a direct access
storage device.
System Action: The IPL or DIAGNOSE X'64' failed.
User Response: Reissue the IPL or DIAGNOSE X'64'
command. If the failure persists, notify your system
operator.
Programmer Response: Resave the segment or
system that failed. A possible cause of the condition is a
bad DASD pack. If another DASD pack is available, use
it to retry the IPL. If the problem persists, contact your
IBM Support Center personnel to diagnose and correct
the software error.
HCP177E Your PARM data exceeds the limit of
nn characters. Correct your data string
and reissue the IPL command.
Explanation: The PARM option on your IPL statement
is followed by a parameter string that exceeds the limit
of characters than can be passed to the system to be
IPLed. The value of nn specifies the maximum length of
the string that can be passed. The largest value nn can
be is 64. If the value of nn is less than 64, the named
saved system specified by the IPL command was
defined by your installation with a PARMREGS range of
less than 16 registers.
Chapter 3. System Messages 153