z/VM: System Messages and Codes Š CP - z/VM - IBM

HCP6085E HCP6089E
command with an increased KEEP limit before
reenabling the trace. (The SIZE option of the TRSAVE
ON command may also have an effect in this situation.
Refer to the description of the TRSAVE command in
z/VM: CP Commands and Utilities Reference for a
discussion of both the KEEP and the SIZE options.)
If you are the owner of a file that was purged, you may
wish to contact the person who entered the TRSAVE or
TRSOURCE command so that the KEEP (and/or SIZE)
limit may be increased.
Operator Response: If you entered the TRSAVE ON
command for CP, you may wish to turn the TRSAVE
function off, then reenter the TRSAVE ON command
with an increased KEEP limit. If the message appears
for a trace ID, you may wish to use the TRSOURCE
command to disable the trace, then enter the TRSAVE
command with an increased KEEP limit before
reenabling the trace. (The SIZE option of the TRSAVE
ON command may also have an effect in this situation.
Refer to the description of the TRSAVE command in
z/VM: CP Commands and Utilities Reference for a
discussion of both the KEEP and SIZE options.)
Otherwise, follow your installation’s procedures for this
situation.
HCP6085E The TRSAVE command cannot be
processed because the function is in a
transition state.
Explanation: A previous TRSAVE ON command has
not completed initialization, and the TRSAVE function is
neither active nor inactive. TRSAVE ON, TRSAVE OFF,
and TRSAVE CANCEL are only valid when the function
is active or inactive.
The previous TRSAVE ON command may not have
completed initialization for the following reasons:
v The tape drive is not ready (TRSAVE FOR CP ON
only).
v The function may be initializing normally after waiting
for a tape drive to become ready (TRSAVE FOR CP
ON only).
v An error occurred, causing a soft abend.
System Action: Command not accepted. System
operation continues.
User Response: Enter the QUERY TRSAVE
command to determine the status of the TRSAVE
function.
You may enter the TRSAVE OFF or TRSAVE CANCEL
commands if the function is active.
You may enter the TRSAVE ON command if the
function is inactive.
348 z/VM: System Messages and Codes — CP
HCP6086I Traceid traceid1 is no longer
superseded by VMGROUP trace
traceid2.
Explanation: The trace ID had previously been
disabled because tracing for the FOR USER trace ID
was superseded by the enabling of the FOR
VMGROUP trace ID.
System Action: The trace ID remains disabled. It is
eligible to be enabled.
User Response: If you want tracing to resume for the
virtual machine specified in the disabled FOR USER
trace ID, you must reenable the FOR USER trace ID
using the TRSOURCE command.
HCP6087E DEFERIO FRAMES specified exceeds
the amount of frames eligible for
DEFERIO traces.
Explanation: No more than a certain percentage
(75%) of the pageable pages in the system dynamic
paging area can be used for active or enabled
DEFERIO traces. The FRAMES parameter of the
TRSAVE command specifies an amount that exceeds
the eligible amount of pageable pages in the system
dynamic paging area that can be used for DEFERIO
traces.
System Action: The command is not executed;
system operation continues.
User Response: Use the QUERY TRSAVE FRAMES
command to determine how many frames are eligible
for DEFERIO traces. Specify an amount of TRSAVE
FRAMES that is within the eligible amount of frames
that can be used for DEFERIO traces.
Note: When a DEFERIO trace is enabled, the sum of
all frames used by active and enabled DEFERIO
traces cannot exceed 75% of the pageable
pages in the system dynamic paging area.
HCP6088I Trace data for traceid traceid[userid]
was not saved by TRSAVE.
Explanation: Generation of trace data for the trace
defined by TRSOURCE traceid is occurring at a rate
faster than the TRSAVE function can collect it.
System Action: The TRSAVE function continues.
User Response: Reduce the amount of trace data
that you are collecting for this trace.
HCP6089E DEFERIO FRAMES specified causes
total DEFERIO frames to exceed the
amount of frames eligible for all
DEFERIO traces.
Explanation: No more than a certain percentage
(75%) of the pageable pages in the system dynamic