z/VM: System Messages and Codes Š CP - z/VM - IBM

HCP1019E HCP1023E
not in an LPAR. If you believe that your configuration
meets these requirements and you receive this
message, contact your IBM software support to
diagnose and correct the problem.
HCP1019E The variations of this message are
explained below.
MESSAGES:
v The POWEROFF option is invalid for a system
running in a Logical Partition.
Explanation: You entered the SHUTDOWN
command with the POWEROFF option, but the
system is currently running in a Logical Partition.
System Action: The command is not executed.
System operation continues.
User Response: Enter the command again without
the POWEROFF parameter.
v The AFTER_POWEROFF option requested is
invalid for a system running in a logical partition.
Explanation: A user entered the SET or QUERY
PROMPT AFTER_POWEROFF command, or the
FEATURES statement in the system configuration file
specified ENABLE/DISABLE PROMPT
AFTER_POWEROFF option, but the machine is in
LPAR mode (logically partitioned).
System Action: System operation continues.
User Response: The AFTER_POWEROFF option is
only supported on ES/9221 processors with the
POWEROFF hardware feature running first level and
not in an LPAR. If you believe that your configuration
meets these requirements and you receive this
message, contact your IBM software support to
diagnose and correct the problem.
HCP1020E The variations of this message are
explained below.
MESSAGES:
v The POWEROFF option is invalid for a system
running as a guest operating system.
Explanation: You entered the SHUTDOWN
command with the POWEROFF option, but the
system is currently running as a guest operating
system in a virtual machine.
System Action: The command is not executed.
System operation continues.
User Response: Enter the command again without
the POWEROFF parameter.
v The AFTER_POWEROFF option requested is
invalid for a system running as a guest operating
system
Explanation: A user entered the SET or QUERY
PROMPT AFTER_POWEROFF command, or the
FEATURES statement in the system configuration file
specified the ENABLE/DISABLE PROMPT
224 z/VM: System Messages and Codes — CP
AFTER_POWEROFF option, but the system is
running as a guest operating system (second level).
System Action: System operation continues.
User Response: The POWEROFF option is only
supported on ES/9221 processors with the poweroff
hardware feature running first level and not in an
LPAR. If you believe that your configuration meets
these requirements and you receive this message,
contact your IBM software support to diagnose and
correct the problem.
HCP1021W SYSTEM SHUTDOWN COMPLETED
WITHOUT REQUESTED POWEROFF
Explanation: The system has been brought to a
successful orderly shutdown. However, the POWEROFF
option that was requested is unable to be performed
because the processor does not have the Poweroff
Hardware feature.
System Action: The system enters a wait state (wait
state code = 1021).
Operator Response: No explicit action is necessary.
You may reload for reinitialization of the CP system at
anytime. The POWEROFF option was accepted by CP,
therefore the IPL will come up Warm automatically, with
no prompting to the system operator.
HCP1022A Enter 1 if you wish to have your
privilege classes unlocked.
Explanation: A CP SET PRIVCLASS command was
entered with the UNLOCK option specified to unlock the
privilege class settings for your own user ID. You must
enter 1 for the command to complete. The command
will terminate with any other response.
System Action: CP goes into CP READ mode and
waits for your response. If you enter a 1, CP issues a
response and your privilege classes are unlocked. The
command terminates with any other response.
User Response: Enter 1 to complete the command
execution, or anything else to terminate the command.
HCP1023E An error was detected while
processing the user’s response. Please
retry the command.
Explanation: An error occurred while handling the
user’s response to the SET PRIVCLASS * UNLOCK
command. The error could be an I/O error, soft abend,
or a miscellaneous system error.
System Action: CP rejects the CP SET PRIVCLASS
command. System operation continues.
User Response: Enter the CP SET PRIVCLASS
command again, and enter a respone of 1.