z/VM: System Messages and Codes Š CP - z/VM - IBM

This message is displayed in conjunction with other
messages that provide information about channel
command word, sense, user ID, and other variables
when necessary.
System Action: System operation continues.
User Response: Record the fault code and the device
address. If the error persists, contact your system
support personnel.
Programmer Response: Examine the EREP outboard
record (OBR) for additional details as to the cause of
the failure. Refer to the hardware publications for sense
data format and descriptions. If a hardware problem
exists, contact your IBM Support Center personnel to
diagnose and correct the hardware problem.
HCP323E DASD rdev {SUBSYSTEM|NON-
VOLATILE} STORAGE IS UNUSABLE -
FAULT CODE = code - {ss-XX-XX|
ssid.p-cc-dd}
Explanation: The DASD subsystem storage (cache)
or nonvolatile storage (NVS) for the specified device
(rdev) is inoperative due to previously reported failures
of a device or of subsystem storage. The variables in
the message are as follows:
code The hardware problem description code.
ss-XX-XX
The physical identifier of the reporting storage
director.
ssid.p-cc-dd
The subsystem identifier, storage path number,
controller identifier, and device unit address of
the affected hardware components
This message is displayed in conjunction with other
messages that provide information about channel
command word, sense, user ID, and other variables
when necessary.
System Action: System operation continues.
Operator Response: Record the fault code and the
device address. If the error persists, contact your
system support personnel.
Programmer Response: Examine the EREP outboard
record (OBR) for additional details as to the cause of
the failure. Refer to the hardware publications for sense
data format and descriptions. If a hardware problem
exists, contact your IBM Support Center personnel to
diagnose and correct the hardware problem.
HCP324I DASD rdev SUBSYSTEM MUST BE
INITIALIZED - FAULT CODE =
code-ss-XX-XX
Explanation: An error occurred during a DASD
subsystem storage operation on the 3880 Model 11 or
21 control unit. The specified storage director
determined that a data loss may have occurred but
cannot determine what, if any, of the data stored in the
DASD subsystem was lost. The variables in this
message are as follows:
rdev The failing device.
code The hardware problem description code.
ss-XX-XX
The physical identifier of the reporting storage
director.
This message is displayed in conjunction with other
messages that provide information about channel
command word, sense, user ID, and other variables
when necessary.
System Action: System operation continues.
User Response: Reinitialize subsystem storage. If the
problem persists, reconfigure to use paging volumes on
another DASD subsystem. Notify your system support
personnel of the problem.
Programmer Response: Examine the EREP outboard
record (OBR) for additional details as to the cause of
the failure. Refer to the hardware publications for sense
data format and descriptions. If a hardware problem
exists, contact your IBM Support Center personnel to
diagnose and correct the hardware problem.
HCP325I DASD rdev STORAGE DIRECTOR
COMMUNICATION FAILED - FAULT
CODE = code - {ss-XX-XX|ssid.p-cc-dd }
Explanation: The other storage director in the
subsystem failed to respond to a communication
attempt, or communication is not allowed because of
the subsystem storage mode switch setting.
The variables in this message are as follows:
rdev The failing device.
HCP323E HCP325I
code The hardware problem description code.
ss-XX-XX
The physical identifier of the reporting storage
director.
ssid.p-cc-dd
The subsystem identifier, storage path number,
controller identifier, and device unit address of
the affected hardware components.
This message is displayed in conjunction with other
messages that provide information about channel
command word, sense, user ID, and other variables
when necessary.
System Action: System operation continues.
User Response: Record the fault code and the device
address. If the error persists, contact your system
support personnel.
Chapter 3. System Messages 165