z/VM: System Messages and Codes Š CP - z/VM - IBM

HCP6757E Internal logic error -- function
terminated.
Explanation: You issued a CP XSPOOL XLISTADD or
CP XSPOOL XLISTDEL command, and CP has
encountered an internal logic error in the XLISTADD or
XLISTDEL processing. Incorrect arguments have been
passed to the subroutine that was to process your
request.
System Action: CP rejects the command; system
operation continues.
User Response: Contact IBM for assistance.
HCP6758E ERROR ENCOUNTERED WHILE
ATTEMPTING TO ACCESS PARM DISK.
Explanation: During the IPL process, CP expected to
find a parm disk but was, for some reason, unable to
access one.
System Action: CP immediately loads a disabled wait
state.
User Response: Make sure that a CMS-formatted
minidisk is present at the location specified by PDOFF,
PDNUM, or PDVOL on the IPL parameters passed to
CP from the Stand-Alone Loader (SAL).
HCP6759I The time zone has changed to zone.
Explanation: A privileged user issued the CP SET
TIMEZONE command to change the system’s local time
zone. The user who issued the command and all other
users logged on to the system will see this message.
System Action: CP changes the local time zone and
presents the appropriate external interrupt to all the
virtual machines that asked CP to notify them of time
zone changes.
User Response: None.
HCP6760E Device rdev is not offline.
Explanation: You issued a CP SET RDEVICE
command that tries to change the characteristics of an
online device.
System Action: CP rejects the request to change the
characteristics of the device at rdev, but continues to
process requests for changes to other devices specified
on the same CP SET RDEVICE command.
User Response: Verify the device number is correct. If
it is correct and not being used, then issue the CP
VARY OFFLINE command for the device and issue
another CP SET RDEVICE command.
HCP6761E The variations of this message are
explained below.
MESSAGES:
HCP6757E HCP6763E
v userid vdev not linked; volume volid marked
draining by Operations personnel.
v Device rdev unavailable; marked draining by
Operations personnel.
Explanation: You see the first version of this message
if you entered a CP LINK command for a minidisk that
resides on a volume marked DRAINING for the LINKS
category.
You see the second version if you entered the SET
DUMP command to a DASD volume that was being
drained by the Operations personnel.
System Action: An error message is issued and
command execution terminates.
User Response: If you receive the first error
message, contact Operations personnel to determine
when the disk will be restarted.
If you receive the second error message, you can enter
the START command to the DASD volume in question
and then enter the SET DUMP command against the
DASD volume.
HCP6762E Frame table entry is outside the
extents of the frame table:
mmmmmmmm-nnnnnnnn.
Explanation: You entered a CP LOCATE FRMTE
command with the ENTRY option specifying an entry for
a frame table address that is outside the range of pages
that the frame table occupies.
System Action: CP ignores the command; system
operation continues.
User Response: Reissue the CP LOCATE FRMTE
command with a valid range of page addresses. You
can do so by specifying a range between the values of
mmmmmmmm and nnnnnnnn.
HCP6763E Specified date and time combination is
impossible.
Explanation: During the IPL process, you (the system
operator) gave CP a time and date that information on
the TIMEZONE_BOUNDARY statements says is
impossible. For example, if you are on the east coast of
the United States, you will receive this message if you
tell the system that it is 2:30 AM EST on April 27, 1991,
because that is the date when the time changes from
2:00 AM to 3:00 AM.
System Action: CP prompts the system operator for
the date and time again.
User Response: Enter a valid date and time.
Chapter 3. System Messages 397