z/VM: System Messages and Codes Š CP - z/VM - IBM

Then reenter the command.
HCP2880E userid vaddr is not linked, CSE LINK I/O
error, code cc.
Explanation: The minidisk vaddr, owned by user
userid, cannot be linked as requested because CSE
received an I/O error when trying to read or write the
CSE track. The error code, cc, describes one of the
following I/O errors:
Code Meaning
01 A write error occurred.
02 The CSE track does not contain the expected
CSE format, or the drive presented a real
hardware I/O error.
03 The CSE map record length on the CSE track
is smaller than the start cylinder for this
minidisk. This indicates that an incorrect CYL
operand was specified on a CSELVOL or
CSELDEV macro.
04 An I/O error occurred because of invalid
channel command words.
05 A hardware error occurred.
System Action: The requested link is denied.
User Response: Make sure that the device where the
minidisk is located is not presenting real hardware I/O
errors and that the volume is correctly formatted for
CSE.
HCP2881E XLINK RESET is not allowed. There is
no CSE LINK control on this system.
Explanation: An XLINK RESET sysname command
was entered on a system identified in HCPSYS as
being excluded from the CSE complex.
System Action: The command is not processed.
User Response: Make sure that you are using the
XLINK RESET command on a CSE-controlled system.
HCP2882E XLINK RESET is not allowed. There is
no CSE LINK control on system
sysname.
Explanation: An XLINK RESET sysname command
was entered, but the specified system is not identified in
HCPSYS as being a member of the CSE complex.
System Action: The command is not processed.
User Response: Make sure that you are specifying
the correct system name and that the correct CSE
system table is active on your system.
HCP2883I Volume volidn is not controlled by CSE
LINK.
Explanation: An XLINK CHECK command was
entered. The volume volidn is not under control of CSE
according to the CSELVOL INCLUDE and CSELVOL
EXCLUDE lists that are currently active on this system.
System Action: The command is processed, and
system operation continues.
User Response: If this volume should be under
XLINK control, it must be added to the CSELVOL macro
operands in HCPSYS.
HCP2884I Volume volidn is controlled by CSE
LINK.
Explanation: An XLINK CHECK command was
entered. The volume volidn is under control of CSE
according to the CSELVOL INCLUDE and CSELVOL
EXCLUDE lists that are currently active on this system.
System Action: The command is processed, and
system operation continues.
User Response: If this volume should not be under
XLINK control, it must be deleted from the CSELVOL
macro operands in HCPSYS.
HCP2885E Volume volidn is offline.
Explanation: The volume volidn is offline and cannot
be acted upon by CSE.
System Action: The command is not processed.
User Response: Vary the volume online and reenter
the command.
HCP2886D Are you ready for XLINK RESET of
system sysname, volume volidn? Enter
YES or NO:
Explanation: You have entered an XLINK RESET
command to reset the link flags for system sysname on
volume volidn.
System Action: None until you reply YES or NO.
User Response: Before replying YES:
HCP2880E HCP2886D
v Make sure you typed the command correctly.
v Make sure the system sysname is really down or has
no access to volume volidn anymore.
v Enter a SYSTEM RESET command and a SYSTEM
CLEAR command on the down system to make sure
that it will not complete any outstanding I/Os or issue
any new I/Os to the volume(s) being RESET.
v If this is a RESET for one volume while another
system is still running, make sure that the volume is
detached from that system on the system being
RESET.
Chapter 3. System Messages 325