z/VM: System Messages and Codes Š CP - z/VM - IBM

HCP410E HCP421E
STOP and START buttons, or until the operator enters a
START command at the console.
Operator Response: Check the form for alignment.
Press the STOP and START buttons to get an
alignment page. Each time an alignment page is
printed, the printer idles. You can either press the STOP
and START buttons to get another alignment page or,
when the paper is properly aligned, you can issue the
START command to print the entire file.
HCP410E The variations of this message are
explained below.
MESSAGES:
v CP ENTERED; PAGING ERROR
v Command terminated; paging error
v Request terminated; paging error
Explanation: An error occurred during paging. This is
probably a hardware error.
System Action: System operation continues. The
virtual machine enters console function mode. If the
virtual machine was running disconnected and no action
occurs within 15 minutes, CP logs off the virtual
machine.
User Response: Reload the virtual system to
continue. If the problem persists, contact your system
support personnel.
Operator Response: If the error is from paging to
DASD, examine the console messages and LOGREC
records to find the DASD that is causing the paging
error. If the problem persists, contact your IBM Support
Center personnel to diagnose and correct the hardware
error.
HCP413E Command processing cannot complete
due to a spool paging error.
Explanation: An I/O error occurred while the system
was attempting to read or write a spooling page to or
from a direct access storage device.
System Action: Command processing terminates;
system operation continues.
User Response: The command terminates, but the
results vary, depending on the command. If you issued
the START command with the IMG option, this caused
the device to DRAIN. If you issued the TAG command,
the tag is not updated. If you issued the CHANGE
command, the file will appear to be changed, but the
changes will not survive a system restart. Check the
extent of command execution and reissue the command
as required. If the problem persists, notify your system
support personnel.
Programmer Response: Contact your IBM Support
Center personnel to diagnose and correct the problem.
172 z/VM: System Messages and Codes — CP
HCP415E Six continuous paging errors have
occurred on DASD nnnn volume volser.
Explanation: Six consecutive paging I/O errors have
occurred on the same volume. The variables are:
nnnn The real device number of the DASD
volser The volume serial number
System Action: A paging error is sent to the requestor
of the paging operation. The requestor determines the
system action to be taken.
User Response: None.
Operator Response: Check the paging device for
possible hardware problems.
HCP417E {rdev|vdev} is not an output spooling
device.
Explanation: The device specified must be an output
spooling device. Valid devices are printers and punches.
System Action: The command is not executed;
system operation continues.
User Response: Reissue the command with a valid
output device specified.
HCP418E {rdev|vdev} is not a spooled device.
Explanation: The device specified is not a spooled
device. For a real device, the device must be a
nondedicated reader, printer, or a punch. For a virtual
device, the device must be a console or a nondedicated
reader, printer, or a punch.
System Action: The command is not executed;
system operation continues.
User Response: Reissue the command specifying a
spooled device.
HCP419E {rdev|vdev} is not a spooled printer.
Explanation: The specified device is not a spooled
printer.
System Action: The command is not executed;
system operation continues.
Operator Response: Reissue the command,
specifying the address of a spooled printer.
HCP421E Printer prt-type does not support the
{feature feature|command command}.
[UCS_name is the name of the UCS
associated with the currently installed
print band|The UCS could not be
loaded or read]
Explanation: The printer (1403, 3203, 3262, 3800,
4245 or 4248) specified in the command does not have
the capabilities to perform the function requested.