z/VM: System Messages and Codes Š CP - z/VM - IBM

HCP2869I HCP2877E
If the format operation should continue, answer YES.
Otherwise, answer NO.
HCP2869I CSE XLINK FORMAT COMPLETE
Explanation: The XLINK FORMAT command
completed without errors.
System Action: System processing continues.
User Response: None.
HCP2870E ERROR nnn ON CMSSTOR CALL
Explanation: The cross-system link facility utility
program could not obtain enough free storage to
complete the requested function. The error code nnn is
the code received from the CMSSTOR macro. See
z/VM: CMS Commands and Utilities Reference manual
for more information on the CMSSTOR error messages.
System Action: The command is not processed.
User Response: You may need more available CMS
free storage. The cross-system link facility utility
program needs enough storage to contain all of the
CSE map records at the same time. If you are
displaying or formatting a track with many large map
records, you may need to increase your available free
storage. Possible methods of increasing free storage
include defining a larger virtual machine with the CP
DEFINE STOR command, or freeing some currently
allocated storage by releasing accessed disks or using
the NUCXDROP command to cancel nucleus
extensions and release the storage occupied by the
corresponding program.
HCP2871E INVALID OPTION: option
Explanation: The specified option option is invalid.
System Action: The command is not processed.
User Response: Reenter the command with valid
options.
HCP2872E COMMAND LINE IS TOO LONG FOR
CP. CP CAN ACCEPT NO MORE THAN
240 CHARACTERS - YOUR COMMAND
WAS nnn CHARACTERS IN LENGTH
Explanation: The length of the XLINK command that
was entered exceeds 240 characters and cannot be
passed from the cross-system link facility utility program
to CP. The nnn variable is the actual length of the
command entered.
System Action: The command is not processed.
User Response: Reenter the command with fewer
parameters. If necessary, enter the command more than
once.
324 z/VM: System Messages and Codes — CP
HCP2873E MISSING OR INVALID PARAMETER OR
OPTION
Explanation: One of the parameters or options is
missing or invalid.
System Action: The command is not processed.
User Response: Reenter the command with valid
parameters and options.
HCP2874E {Device vdev|Volume volid} is not a
CKD or ECKD DASD device.
Explanation: The virtual device or volume specified is
not a CKD or ECKD DASD. CSE supports only CKD
and ECKD DASD. The requested function cannot be
completed.
System Action: The command is not processed.
User Response: Make sure that the device you want
to address is a CKD or ECKD DASD. Then reenter the
command.
HCP2876I VOLUME volid WAS FORMATTED FOR
CSE ON mm/dd/yy AT hh:mm:ss BY
USER userid AT SYSTEM sysname
Explanation: The above message is followed by this
message:
-CYL- READ/WRITE FLAGS ON volid (CYL=c
TRK=t RECL=l RECS=r SYSTEMS=s)
ccc mode sysname2
- or -
--- NO LINK FLAGS ON THIS VOLUME
This message is issued when the XLINK DISPLAY
function is requested. It informs you when and by whom
the volume was formatted for CSE use.
System Action: The system continues to process the
command.
User Response: None.
HCP2877E EITHER NOT A CSE VOLUME, OR CSE
DATA IS NOT ON CYL ccccc TRK tt
Explanation: The volume for which you requested an
XLINK DISPLAY may not be a CSE-controlled volume.
There is no valid CSE data on cylinder ccccc, track tt.
System Action: The command is not processed.
User Response: Make sure that:
v The correct CSELVOL INCLUDE list was used
v The volume was correctly formatted for CSE
v The parameters specified on the CSELVOL INCLUDE
list embedded in the cross-system link facility utility
program were the same as those used when the
volume was formatted for CSE.