z/VM: System Messages and Codes Š CP - z/VM - IBM

updated and processing continues.
User Response: None
HCP9951E Invalid LKFAC configuration name
entered
Explanation: The Multi-Path Lock Facility (MPLF)
RPQ simulation configuration name specified on the
SET LKFAC command:
v contains more than 8 characters, or
v does not consist of alphanumeric characters in the
range A to Z.
System Action: The request is ignored.
User Response: Re-enter the SET LKFAC command
using a 1- to 8-character alphanumeric configuration
name.
HCP9952E Maximum (8) users assigned to LKFAC
configuration config_name
Explanation: The maximum number of users allowed
to be connected to the Multi-Path Lock Facility (MPLF)
RPQ simulation configuration is already assigned. The
maximum number allowed is 8.
System Action: The request is ignored.
User Response: None.
HCP9954E Maximum LKFAC configurations
defined, config_name not created
Explanation: The configuration name table does not
contain an available entry to hold the new Multi-Path
Lock Facility (MPLF) RPQ simulation configuration. The
maximum number of configurations is 250.
System Action: The request is ignored.
User Response: None.
HCP9955I No change, LKFAC configuration same
as entered
Explanation: There is no difference between the
specified name and the name currently in use for the
Multi-Path Lock Facility (MPLF) RPQ simulation
configuration.
System Action: The request is ignored.
User Response: Re-enter the SET LKFAC request
with a different name to join a new configuration.
Otherwise, no response is necessary.
HCP9961E LKFAC CONFIGURATION config_name
CANNOT BE FOUND
Explanation: The QUERY processor cannot locate the
specified Multi-Path Lock Facility (MPLF) RPQ
simulation configuration name in the configuration name
table.
System Action: The request is ignored.
User Response: Re-enter the QUERY LKFAC request
with the correct configuration name. Use QUERY
LKFAC ALL to display a list of active configuration
names.
HCP9962E userid not attached to a LKFAC
configuration
Explanation: The QUERY LKFAC command was
issued without a name specified for the Multi-Path Lock
Facility (MPLF) RPQ simulation configuration. When no
name is specified, the default is normally a display of
information for the user’s attached configuration.
However, in this case the user is not attached to any
configuration.
System Action: The request is ignored.
User Response: Re-enter the QUERY LKFAC request
with the correct configuration name. Use QUERY
LKFAC ALL to display a list of active configuration
names.
HCP9963E No LKFAC configuration defined
Explanation: A QUERY LKFAC was issued, but the
configuration name table was not allocated yet.
Therefore, the Multi-Path Lock Facility (MPLF) RPQ
simulation configuration cannot be added to the table.
System Action: The request is ignored.
User Response: None.
HCP9951E HCP9965E
HCP9964E User not authorized to use LKFAC
simulation support
Explanation: A SET LKFAC command was entered,
but the user was not authorized to use via the OPTION
LKFAC user directory control statement.
System Action: The request is ignored.
User Response: To use the Multi-Path Lock Facility
(MPLF) RPQ simulation support the user must be
authorized to use the SET LKFAC command through
specification in the OPTION LKFAC statement in their
user directory entry.
HCP9965E Unable to write into one of the
IUCV/APPC interrupt buffers.
Explanation: A machine check or protection exception
was detected while attempting to write into one of the
IUCV/APPC interrupt buffers. Possible causes include:
v A DCSS has overlaid one of the interrupt buffers.
v A paging error was detected when attempting to page
in one of the interrupt buffers.
Chapter 3. System Messages 469