z/VM: System Messages and Codes Š CP - z/VM - IBM

v Spool file errors encountered during initialization.
No files have been deleted yet. To continue
restart and delete the files, enter GO. To stop so
you can check spool volumes, enter STOP.
Explanation: Spool files and possibly system data
files will be lost because either spool volumes are
offline or I/O errors occurred on spool volumes.
Message HCP2513I, which is displayed prior to this
message, summarizes the number of spool files and
system data files that will be lost for various reasons.
Messages HCP2506E through HCP2510E may be
displayed with more information about individual
spool file errors or spool volumes that are offline.
Operator Response: Enter STOP to stop
initialization, and start manual recovery actions to
check and correct a possible configuration error. If
previous messages indicate hardware errors, contact
your support personnel (or the IBM Support Center
for assistance) to diagnose and correct the errors, if
possible.
Enter GO to continue initialization, with the loss of the
files as indicated by the previous messages.
v Spool files will be deleted because of COLD start.
No files have been deleted yet. To continue COLD
start and delete files, enter GO. To stop COLD
start without deleting files, enter STOP.
Explanation: Spool files will be discarded from the
system by COLD start.
If message HCP2513I, which is displayed prior to this
message, indicates spool files will be deleted due to
spool volumes being offline or I/O errors on spool
volumes, it is possible system data files will also be
lost. Messages HCP2506E through HCP2510E may
be displayed with more information about individual
spool file errors or spool volumes that are offline.
Operator Response: Enter STOP if you wish to stop
initialization and preserve the previous state of the
spooling system. If errors were indicated, start
manual recovery actions to check and correct a
possible configuration error. If previous messages
indicate hardware errors, contact your support
personnel (or the IBM Support Center for assistance)
to diagnose and correct the errors, if possible.
Enter GO to continue initialization, with deletion of the
files indicated by the previous messages.
v CLEAN start has been selected. This will cause
all spool files and System Data Files (NSS, DCSS,
TRF, IMG, UCR, NLS) to be deleted. No files have
been deleted yet. To continue CLEAN start and
delete files, enter GO. To stop CLEAN start
without deleting files, enter STOP.
Explanation: All spool files and system data files will
be discarded by CLEAN start.
Operator Response: Enter STOP if you want to stop
initialization and preserve the previous state of the
spooling system. None of the existing spool files or
system data files will be deleted. Enter GO to
continue initialization and delete spool files and
system data files.
v Spooling errors were encountered that may cause
loss of system data files. No system data files
have been deleted yet, but continuation of the
system IPL could cause them to be deleted.
Enter GO to continue initialization and risk
deleting system data files.
To stop processing without deleting files, enter
STOP.
Explanation: System data files may be lost because
either spool volumes are offline or I/O errors occurred
on spool volumes.
Message HCP2513I, which was displayed prior to
this message, summarized the number of spool files
and system data files that will be lost for various
reasons. Messages HCP2506E through HCP2510E
may be displayed with more information about
individual spool file errors or spool volumes that are
offline.
Operator Response: Enter STOP to stop
initialization, and start manual recovery actions to
check and correct a possible configuration error. If
previous messages indicate hardware errors, contact
your support personnel (or the IBM Support Center
for assistance) to diagnose and correct the errors, if
possible.
Enter GO to continue initialization and risk deleting
system data files.
System Action: If STOP is entered, system restart is
canceled, and there is no change to the spooling
system.
If GO is entered, system initialization continues, and the
spool files and system data files mentioned above are
deleted.
HCP2512I Spooling initialization complete
Explanation: All spool files have been recovered, the
allocation maps are updated, and the system and user
spool file queues are established.
System Action: System operation continues.
Operator Response: None.
HCP2512I HCP2513I
HCP2513I Spool files {available|on offline
volumes|with I/O or data errors|to be
discarded} - {nnnnnn| NONE}
Total files to be deleted - {nnnnnn}
Explanation: This message provides spool file
summary status after the preliminary phase of spooling
initialization is complete.
System Action: If all spool files are recovered, system
operation continues. If files are to be deleted, the
Chapter 3. System Messages 291