z/VM: System Messages and Codes Š CP - z/VM - IBM

cancel (the ones that contain response 4 with
CANCEL as the reason for termination). Enter
the SPXTAPE SCAN command again for these
volumes.
HCP1851E XF is an invalid option when the device
is not a 3480 with the IDRC hardware
feature installed.
Explanation: The XF option was specified with a
device that is not a 3480 tape with the IDRC (Improved
Data Recording Capability) hardware compaction
feature.
System Action: The command is not executed.
System operation continues.
User Response: Reissue the command with the
number of a 3480 IDRC capable device, or with XF not
specified.
HCP1858I The variations of this message are
explained below:
MESSAGES:
v The non-destructive dump function has
completed.
Explanation: Either a system error initiated a
non-destructive dump, or a privileged user entered
the SNAPDUMP command, and the non-destructive
dump process has finished honoring the request.
Either a dump was taken, or further dump processing
messages indicate why no dump was taken.
System Action: None.
Operator Response: The system may have been
unavailable for an extended period of time prior to the
message being issued. The message indicates the
system is available once again, but the operator will
have to ensure all resources are again online.
Servers that may have timed out or lines that were
dropped may have to be made active once again.
v A non-destructive dump request occurred for
abendMMMMMM. The dump was NOT taken
because a required system resource was
unavailable.
Explanation: A system error requested a
non-destructive dump, but non-destructive dump
processing was unable to obtain a resource.
Therefore no dump was taken. The MMMMMM
variable is the abend code.
System Action: None.
Operator Response: None. If a dump was not taken
at the time of the failure, initiating a dump after this
message is received will be too late to capture the
failing environment. If the same abend indicated
consistently fails to result in a dump, contact your
IBM Support Center for assistance. A problem may
exist if this particular abend should not be using the
non-destructive dump function.
HCP1851E HCP1880E
HCP1876E The user ID userid is a restricted user
ID and may not be specified in the CP
directory.
Explanation: DIRECTXA encountered a user definition
which attempted to use a restricted user ID. Restricted
user IDs are user IDs that may cause CP to function
inappropriately when logged on. Examples of these user
IDs are: LOGN0100, LOGL0001, and LOGV0025.
System Action: The directory program will terminate
without bringing a new directory online, after scanning
the remaining statements for syntax.
User Response: Change the user definition to define
a user ID which is not restricted and reenter the
DIRECTXA command.
HCP1879E statement STATEMENT WITH
{WRKALLEG|NOWRKALLEG} OPTION
FOLLOWING USER userid DOES NOT
APPLY TO VIRTUAL DEVICE vdev
BECAUSE THE {PREVIOUS
STATEMENT IS NOT AN MDISK|DEVICE
IS DEFINED READ-ONLY}
Explanation: You specified a MINIOPT or DASDOPT
that is not valid with the WRKALLEG or NOWRKALLEG
option because the device is defined with read-only
access, or the DASDOPT did not follow an MDISK
statement. To specify the WRKALLEG or
NOWRKALLEG option, the device must be configured
for write access. If WRKALLEG or NOWRKALLEG is
specified with DASDOPT, the DASDOPT must follow an
MDISK statement. It cannot follow DEDICATE or LINK.
System Action: The directory program terminates
after scanning the remaining statements for syntax.
User Response: Determine if the virtual device
specified is the correct device for the WRKALLEG or
NOWRKALLEG option. If so, correct the error resulting
in this message.
HCP1880E CLOSING QUOTATION MARK IS
MISSING FROM QUOTED STRING
FOLLOWING {PROFILE profname|USER
userid}
Explanation: The directory record contains an
incomplete quoted string.
System Action: The directory statement on which the
error occurred is displayed above the message. Only
the first 237 characters of the statement are displayed
above the message. The directory program terminates,
without bringing a new directory on line, after scanning
the remaining statements for syntax.
User Response: Correct the quoted string in the
record and reenter the DIRECTXA command.
Chapter 3. System Messages 257