z/VM: System Messages and Codes Š CP - z/VM - IBM

HCP6805E HCP6812E
R12 Base register
R13 Work page address.
User Response: Load the module lower than or
higher than the offline/bad page frame.
If running HCPSAL, see the section, “Overriding
Stand-Alone Program Defaults” in the z/VM: CP
Planning and Administration.
HCP6805E The variations of this message are as
follows:
MESSAGES:
v Cannot find RDEV for TYPE 1 subchannel
v Cannot determine partition being changed by this
dynamic I/O request
Explanation: You tried to dynamically change your I/O
configuration, but CP rejected your request because of
an internal hardware error.
System Action: CP ignores your dynamic I/O change
request and normal processing continues.
User Response: Contact your IBM software support
for programming support.
HCP6806E Dynamic I/O change request [for
channel path|for control unit|for
device] failed with return code nnnn
Explanation: You used one of the dynamic I/O
commands to dynamically change your I/O
configuration, but the command failed with the specified
return code (nnnn).
System Action: CP ignores your dynamic I/O change
request and normal processing continues.
User Response: Fix the problem associated with the
specified return code (nnnn) and enter the dynamic I/O
command again. For more information about the return
code, see the z/VM: I/O Configuration book.
HCP6807E Device rdev is being throttled and
cannot be attached to the system as a
CP-owned device.
Explanation: You tried to attach a CP-owned device,
but CP rejected your request because the device you
specified is currently being throttled. CP does not allow
you to throttle CP-owned devices.
System Action: CP ignores your dynamic I/O change
request and normal processing continues.
User Response: Enter a SET THROTTLE rdev OFF
command to stop throttling the specified device. Then
attach that device to the system again. (For more
information about the SET THROTTLE command, see
the z/VM: CP Commands and Utilities Reference.)
404 z/VM: System Messages and Codes — CP
HCP6808E The variations of this message are as
follows:
MESSAGES: System disabled for dynamic I/O
changes
v The configuration mode setting of the hardware
and software do not match
v The dynamic I/O support was disabled at the
service console
v Cannot store LPAR data
v The VM configuration token does not match the
hardware configuration token
v Cannot find the configuration token on the
system
Explanation: You tried to dynamically change your I/O
configuration, but CP rejected your request.
System Action: CP ignores your dynamic I/O change
request and normal processing continues.
User Response: Fix the problem associated with the
message text variation and enter the dynamic I/O
command again.
HCP6809E This processor does not support the
dynamic I/O changes
Explanation: You tried to dynamically change your I/O
configuration, but CP rejected your request because the
processor that CP is running is not capable of
supporting dynamic I/O changes. Only Parallel 390
processors support the dynamic I/O configuration
feature.
System Action: CP ignores your dynamic I/O change
request and normal processing continues.
User Response: None, until you switch to a Parallel
390 processor.
HCP6811E Vary {online|offline} CHPID nn failed
with return code nnnn.
Explanation: You used the VARY CHPID command to
vary a channel path online or offline, but the command
failed with the specified return code (nnnn).
System Action: Command execution terminates and
system operation continues.
User Response: Fix the problem associated with the
specified return code (nnnn) and enter the VARY CHPID
command again. For more information about the return
code, see the z/VM: I/O Configuration book.
HCP6812E Set IOCDS_active command failed with
return code nnnn
Explanation: You used the SET IOCDS_ACTIVE
command to switch the active I/O configuration data set
(IOCDS) file, but the command failed with the specified
return code (nnnn).